Unitree G1- Flagship Version C End G1 Edu Flagship Edition C
तपशील
- Product Name: G1 – Flagship Version C End INSPIRE Dexterous Hand
- आवृत्ती: 1.0
- Manufacturer: Unitree Robotics
- Usage: Civilian robot
After installing the dexterous hand, avoid movements such as squatting and lying down to prevent damage. This product is a civilian robot. We kindly request that all users refrain from making any dangerous modifications or using the robot in a hazardous manner. Please visit Unitree Robotics Webअधिक संबंधित अटी आणि धोरणांसाठी साइट, आणि स्थानिक कायदे आणि नियमांचे पालन करा.
Disassembly सूचना
Step1: Remove the Cover Plate
Remove two M2 screws from the hand section, then extract the cover plate as shown in the figure below.
Step2: Remove the INSPIRE Dexterous Hand
Remove two M3 screws, take out the clamp (mind the cables), and then remove the INSPIRE dexterous hand, as shown below.
Step3: Remove the cable clips
Remove one M4 screw and take out Cable Clamp
- Remove two M4 screws and take out Cable Clamp
- Remove two M4 screws and take out Cable Clamp 3. Remove two M4 screws and take out Cable Clamp २, खाली दाखवल्याप्रमाणे.
Step4: Disconnect the Connector
Unplug the connector, as shown below.
स्थापना सूचना
Step1: Install the Fixed Base, Signal Cable Circuit Board, and Fixed Cover
Remove two M6 screws, take out the handle, place the fixed base, reinstall the handle, and tighten the two M6 screws.Place the signal cable circuit board, install the fixed cover, and tighten two M4 screws.
Step2: Install the INSPIRE Dexterous Hand
Before installing the hand, distinguish between left and right hands (method as shown).
Place the dexterous hand, install the clamp (mind the cables), and tighten two M3 screws.
Step3: Install the cover plate
Place the cover plate, protect the cables, and tighten two M2 screws, as shown below.
Step4: Install Cable Clamps
Place Cable Clamp 1 and tighten one M4 screw. Place Cable Clamp 2 and tighten two M4 screws. Place Cable Clamp 3 and tighten two M4 screws. Place Cable Clamp 4 and tighten two M4 screws, as shown below.
Note: There are four bolded sections on the cable. These correspond to Cable Clamps 1-4. Ensure thebolded sections are securely clamped to fix the cables properly!
Step5: Connect the Connector
Plug in the connector firmly, as shown below.
Step6: Complete the installation
- Attention!!! When installing the three-fingered dexterous hand, please do not press the cable to avoid damaging the cable and causing poor contact!
- Attention!!! After installing the dexterous hand, avoid movements such as squatting and lying down to prevent damage!!!
वारंवार विचारले जाणारे प्रश्न
Q: How do I avoid damaging the cables during installation?
A: When installing the three-fingered dexterous hand, avoid pressing the cables to prevent cable damage and poor contact.
Q: What movements should be avoided after installing the dexterous hand?
A: Avoid movements such as squatting and lying down to prevent damage to the product.
कागदपत्रे / संसाधने
 |
Unitree G1- Flagship Version C End G1 Edu Flagship Edition C [pdf] वापरकर्ता मार्गदर्शक G1- Flagship Version C End, G1- Flagship Version C End G1 Edu Flagship Edition C, G1- Flagship Version C End, G1 Edu Flagship Edition C, Edu Flagship Edition C, Flagship Edition C, Edition C |