वापरकर्ता मॅन्युअल
DS-DMX45 and DS-WDMX45
DS-DMX45
4-Channel DMX/RDM Decoders
महत्त्वाचे: स्थापनेपूर्वी सर्व सूचना वाचा.
सुरक्षा आणि नोट्स
- उत्पादन लागू राष्ट्रीय, राज्य आणि स्थानिक बिल्डिंग आणि इलेक्ट्रिकल कोड नुसार स्थापित आणि सर्व्हिस केले पाहिजे.
- विद्युत शॉकचा धोका कमी करण्यासाठी, कोणतीही स्थापना किंवा वायरिंग प्रक्रिया करण्यापूर्वी मुख्य उर्जा स्त्रोत आणि सर्किट ब्रेकर बंद असल्याची खात्री करा.
- DMX सिग्नल amplifier required if more than 32 decoders are connected or when using overlong signal line. Signal ampलिफिकेशन सतत 5 वेळा जास्त नसावे.
- If recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W 90-120Ω terminal resistor at the end of each DMX signal line.
- Display Alarms: OLA=Overload alarm, OHA=Overheat alarm. Check product label for specific electrical specifications related to installation.
अयोग्य स्थापना वॉरंटी रद्द करेल.
सिस्टम सेटिंग्ज
- Enter system parameter setup: Long press M and
key at the same time for 2s (SETUP on DS-WDMX45) for decode mode, gray level, output PWM frequency, output brightness curve, default output level, automatic blank screen. Short press M key (SETUP on DS-WDMX45) to switch parameters. - Decode mode: short press or
key to switch 1/2/4 channel decode mode (d-1, d-2, or d-4). When set as 1 channel decode, the decoder only occupies 1 DMX address and all four channel outputs have the same brightness of that address. - Gray level: short press or ► key to switch 8 bit (b08) or 16 bit ( b16). Choose 16 bit if the DMX master supports 16 bit.
- Output PWM frequency: short press or key to switch 250Hz (F02), 500Hz ( F05 ), 1000Hz ( F10 ), 2000Hz (F20), 4000Hz (F40), 8000Hz (F80), 16000Hz (F16), or 32000Hz (F32). Higher PWM frequency will cause lower output current and higher power noise but is more suitable for camera (no flicker for video).
- When PWM frequency > 8000Hz it is necessary to reduce the output current per channel: 16000Hz (4x 3A @ 12-48V), 32000Hz (4x 2.5A @ 12-24V or 4x 2A @ 36-48V).
- Output brightness curve: short press or key to switch to linear curve (C-L) or logarithmic curve (C-E).
- Default output level: set output level when no DMX input signal. Short press or key to switch maintain DMX output (d- -) or output default level (d00 to dFF, 0-100%), long press or key to change output default level.
- Automatic blank screen: short press or key to turn on (bon) or turn off (boF) automatic blank screen function.
- Long press M key (SETUP on DS-WDMX45) for 2s to exit setup or it will automatically timeout after 10s.
टीप: मॅन्युअल बटण ऑपरेशन सेटिंग्ज व्यतिरिक्त, वरील सिस्टम पॅरामीटर्स RDM फंक्शनद्वारे देखील सेट केले जाऊ शकतात.
मंद वक्र सेटिंग
डीएमएक्स मोड
- Decoder automatically enters DMX mode when input signal is present.
- Manual DMX mode: press M key (MODE on DS-WDMX45). until display shows 001~999.
- Press ◄ or ► button to change DMX decode start address (001-999). Long press for faster adjustment.
- Each DMX decoder occupies four DMX addresses. Default start address is 1. See the table for the corresponding relationships.
| DMX कन्सोल | DMX डीकोडर आउटपुट |
| CH1 0-255 | CH1 PWM 0-100% (LED R) |
| CH2 0-255 | CH2 PWM 0-100% (LED G) |
| CH3 0-255 | CH3 PWM 0-100% (LED B) |
| CI-14 0-255 | CH4 PWM 0-100% (LED W) |
Stand-alone RGB/RGBW Mode
- स्टँड-अलोन RGB/RGBW मोड एंटर करा जेव्हा DMX सिग्नल डिस्कनेक्ट किंवा हरवला असेल.
- Short press M key (SETUP on DS-WDMX45) until display shows P01~P30.
- दाबा or key to change dynamic mode number (P01-P30).
- Speed and brightness can be adjusted for each mode.
- Long press M key (SETUP on DS-WDMX45) for 2s to enter setup mode for speed, RGB brightness, and W channel brightness.
- Short press M key (MODE on DS-WDMX45) to switch between the three settings.
- दाबा or key to setup the value of each setting.
- मोड गती: 1-10 स्तर गती (S-1, S-9, SF).
- Mode RGB brightness: 1-10 level brightness (b-1, b-9, b-F).
- White channel brightness: 0-255 level brightness (400-4FF).
- Long press M key (SETUP on DS-WDMX45) for 2s to exit. It will automatically exit with no input for 10s.
RGB/RGBW Modes
| नाही. | नाव | नाही. | नाव | नाही. | नाव |
| P01 | स्थिर लाल | P11 | ग्रीन स्ट्रोब | P21 | Red/Yellow Smooth |
| P02 | स्थिर हिरवा | P12 | निळा स्ट्रोब | P22 | Green/Cyan Smooth |
| P03 | स्थिर निळा | P13 | पांढरा स्ट्रोब | P23 | Blue/Purple Smooth |
| PO4 | स्थिर पिवळा | P14 | आरजीबी स्ट्रोब | P24 | Blue/White Smooth |
| P05 | स्थिर सायन | P15 | 7-color Strobe | P25 | RGB + W Smooth |
| P06 | स्थिर जांभळा | P16 | Red Fade In and Out | P26 | RGBW Smooth |
| P07 | स्थिर पांढरा | P17 | Green Fade In and Out | P27 | RGBY Smooth |
| P08 | आरजीबी जंप | P18 | निळा फिकट आत आणि बाहेर | P28 | Yellow/Cyan/Purple Smooth |
| P09 | 7 रंग उडी | P19 | White Fade In and Out | P29 | RGB Smooth |
| P10 | लाल स्ट्रोब | P20 | RGBW Fade In and Out | P30 | 6 Color Smooth |
Stand-alone Dimmer Mode
- DMX सिग्नल डिस्कनेक्ट किंवा हरवल्यावरच स्टँड-अलोन डिमर मोडमध्ये प्रवेश करा.
- Short press M key (MODE on DS-WDMX45) until screen displays L-1~L-8.
- दाबा or key to change dimmer mode number (L-1~L-8).
- Each dimmer mode allows for independent brightness adjustment of each channel.
- Long press M key (SETUP on DS-WDMX45) for 2s to enter setup for channel brightness.
- Short press M key (SETUP on DS-WDMX45) to switch between the four channels
- दाबा or key to set brightness value for each channel. (100-1FF, 200-2FF, 300-3FF, 400-4FF).
- Long press M key (SETUP on DS-WDMX45) for 2s to exit. It will automatically exit with no input for 10s.
फॅक्टरी डीफॉल्ट पॅरामीटर पुनर्संचयित करा
- Long press ◄ or ► key for 2s to restore factory default settings (screen displays RES).
- Factory default settings: DMX decode mode, DMX decode start address is 1, four channel decode, 8-bit gray level, 2000Hz PWM frequency output, logarithmic brightness curve, output 100% level when no DMX input is present, RGB mode number is 1, dimmer mode number is 1, automatic blank screen is off.
समस्यानिवारण
| खराबी | कारणे | समस्यानिवारण |
| प्रकाश नाही | 1. शक्ती नाही 2. Incorrect or loose connection |
1. शक्ती तपासा 2. Check the connection |
| चुकीचा रंग | 1. चुकीची वायरिंग 2. DMX decode address error |
1. वायरिंग तपासा 2. Set correct decode address |
| व्हॉल्यूमसह, समोर आणि मागील दरम्यान असमान तीव्रताtagई ड्रॉप | 1. Output cable is too long 2. Wire diameter is too small 3. वीज पुरवठा क्षमतेपेक्षा जास्त ओव्हरलोड |
1. Reduce cable length 2. Change to higher gauge wire 3. जास्त वॅटने बदलाtagई वीज पुरवठा |
Rev तारीख: V3 10/15/2025
4400 Earth City Expy, St. Louis, MO 63045 • ५७४-५३७-८९००
superbrightleds.com
कागदपत्रे / संसाधने
 |
superbrightleds DS-DMX45, DS-WDMX45 4-Channel DMX/RDM Decoders [pdf] वापरकर्ता मॅन्युअल DS-DMX45, DS-WDMX45, DS-DMX45 DS-WDMX45 4-Channel DMX RDM Decoders, DS-DMX45 DS-WDMX45, 4-Channel DMX RDM Decoders, DMX RDM Decoders, Decoders |