SR-MT9041A-R ZigBee ड्युअल टेक स्मार्ट रिले मॉड्यूल
“
तपशील:
- Product: Matter Over Thread + ZigBee Dual Tech Smart Relay
मॉड्यूल - इनपुट व्हॉल्यूमtagई: 100-240Vac
- आउटपुट व्हॉल्यूमtagई: 100-240Vac
- कमाल लोड करंट:
- प्रतिरोधक भार: कमाल. 4.3A
- कॅपेसिटिव्ह/इंडक्टिव्ह लोड: कमाल. 1.7A
- स्टँडबाय वीज वापर: 3W
उत्पादन वापर सूचना:
ऑपरेशन:
- कनेक्शन आकृतीनुसार वायरिंग करा.
- This device is a wireless receiver compatible with Matter
प्रणाली - Add to a Matter platform and control through the platform using
an Apple HomePod mini as a Matter border router.
Touchlink and Reset:
- To start Touchlink pairing, short press the Reset button 4
वेळा - Bring the remote within 10cm of the receiver and set it into
टचलिंक जोडणी मोड. - Indication on the remote will confirm successful link.
Learning to a Zigbee Green Power Switch:
- Short press Reset button 4 times to start Learning mode.
- Set the green power switch into Learning mode.
- Indication on the switch will confirm successful learning.
Wiring Diagram Notes:
एल - थेट आघाडीसाठी टर्मिनल
एन - तटस्थ आघाडीसाठी टर्मिनल
L-out – output terminal of the relay (controlling connected light
स्रोत)
S – terminal for switch
बाह्य स्विच प्रकार:
There are two firmware versions available, one for push switch
and the other for toggle on/off switch. Confirm the external switch
type before ordering.
वारंवार विचारले जाणारे प्रश्न:
Q: What if the connected light has a smaller power consumption
when using the device without a neutral wire?
A: If the connected light has a smaller power consumption, a
Bypass is needed for the device to operate, requiring at least 3W @
240 VAC of power consumption.
"`
Matter Over Thread + ZigBee Dual Tech Smart Relay Module
महत्वाचे: इंस्टॉलेशन फंक्शन परिचय करण्यापूर्वी सर्व सूचना वाचा
42 मिमी
Reset Manual
एल-आउट
S
L
N
38 मिमी
Network pairing, touchlink and reset to factory setting Manual to turn on/off the load
अॅक्सेसरी १: वायर क्लॅम्पamp कव्हर. वेगळे खरेदी करावे लागेल.
ऑपरेशन
1. कनेक्शन डायग्रामनुसार वायरिंग योग्यरित्या करा.
२. हे मॅटर थ्रेड डिव्हाइस एक वायरलेस रिसीव्हर आहे जे विविध मॅटर सुसंगत प्रणालींशी संवाद साधते. हे रिसीव्हर सुसंगत मॅटर प्रणालीकडून वायरलेस रेडिओ सिग्नल प्राप्त करते आणि नियंत्रित करते.
3. Add to a Matter platform and control through the platform: Note: An Apple HomePod mini is used as a Matter border router for adding and controlling the device. For other Matter border routers, please refer to their user manuals to learn how to add and control Matter devices. Step 1: Prepare an iPhone (iOS 16.2 or later) or iPad (iPadOS 16.2 or later) with the latest version firmware, and prepare an Apple HomePod mini with the latest version firmware.
पायरी २: तुमच्या घरातील WLAN नेटवर्कशी iPhone किंवा iPad कनेक्ट करा. Apple Home अॅप चालवा आणि Apple ने दिलेल्या सूचनांनुसार HomePod मिनी सेट करा (आकृती १ ते आकृती ७ मध्ये दाखवल्याप्रमाणे).
16 मिमी
अॅक्सेसरी २: डिन रेल ब्रॅकेट. वेगळे खरेदी करावे लागेल.
उत्पादन डेटा
इनपुट व्हॉल्यूमtage 100-240Vac
आउटपुट व्हॉल्यूमtage 100-240Vac
कमाल लोड करंट
Resistive load: max. 4.3A, Capacitive/Inductive load: max. 1.7A
स्टँडबाय वीज वापर
<=0.5W
· Matter over Thread + ZigBee dual tech in wall smart relay module · Supports resistive loads, capacitive loads or inductive loads · 1 channel output, max. load up to 4.3A · Input and Output with Screw Terminals, Safe and Reliable · Enables to control ON/OFF of connected light source · App control + Touchlink remote control + Green Power kinetic switch control · App control through Matter (e.g. Apple Home, Amazon Alexa, Google Home) · Fully compatible with universal Matter ecosystems from different manufacturers · Active power and energy metering functionality · Mini Size, Easy to be Installed into a standard size wall box
सुरक्षा आणि इशारे
· डिव्हाइसवर लागू केलेल्या पॉवरसह स्थापित करू नका. · यंत्राला ओलावा लावू नका.
आकार (LxWxH) ४२x३८x१६ मिमी
आकृती 1 आकृती 3
आकृती 2 आकृती 4
आकृती 5 आकृती 7 आकृती 9
Step 3: Do wiring of the Matter thread relay according to the wiring diagram and power on it.
Step 4: Add the Matter thread relay to the Apple Home app by scanning the QR code sticker on the relay as shown in Figure 8 to Figure 15.
आकृती 6 आकृती 8
आकृती 11
आकृती 12
Note: Before scanning the QR coder sticker on the relay as shown in Figure 10, short press the reset button 5 times to reset the relay so that it can be discovered by the Apple Home app. Otherwise if it has already been added to another gateway, current gateway can not discover and add it.
आकृती 10
आकृती 13
आकृती 14
Note: When choose the room that you would like to add the relay to, please make sure to choose the same room that the HomePod mini is located as shown in Figure 13.
आकृती 15
आकृती 16
Step 5: once the relay is added to the gateway successfully, tap on the device to control on/off of the relay as shown in Figure 16 to Figure 18.
आकृती 17
आकृती 18
4. फॅक्टरी सेटिंग्ज पुनर्संचयित करा
फॅक्टरी सेटिंग्ज पुनर्संचयित करण्यासाठी, "रीसेट" बटण 5 वेळा दाबा किंवा पुढील क्रमाने डिव्हाइस चालू आणि बंद करा. जर डिव्हाइस यशस्वीरित्या रीसेट केले गेले, तर कनेक्ट केलेला लाईट यशस्वी रीसेट दर्शविण्याकरिता 3 वेळा ब्लिंक करेल.
स्विच ऑन स्विच ऑफ
<1एस
5 एस-15 एस
<1S <1S
<1एस
> 3 एस
>3S >3S >3S >3S
८. झिग्बी रिमोटला स्पर्श करा.
पायरी १: टचलिंक पेअरिंग सुरू करण्यासाठी "रीसेट" बटण ४ वेळा दाबा. पायरी २: रिमोट रिसीव्हरपासून १० सेमी अंतरावर आणा. पायरी ३: रिमोट टचलिंक पेअरिंगमध्ये सेट करा, कृपया त्याचे मॅन्युअल पहा. पायरी ४: यशस्वी लिंकसाठी रिमोटवर संकेत असेल आणि कनेक्ट केलेला लाईट फ्लॅश होईल.
Note: There are two control situations: 1) Only one remote, to control one or more receivers: directly perform Touchlink pairing between the remote and the receiver. 2) Only one receiver, to be controlled by multiple remotes, or multiple remotes and multiple receivers with cross-control: use one receiver as the Zigbee hub, add all remotes and other receivers to the hub, and then perform Touchlink pairing between the remotes and the receivers. The steps are as follows: Step 1: Use one receiver as the Zigbee hub and short press “Reset” button 4 times to start adding Zigbee devices. Step 2: Reset power of another receiver once to enter Zigbee network pairing mode, it will be added by the hub, and the connected light will flash. Step 3: Set a Zigbee remote to enter Zigbee network pairing mode, it will be added by the hub, and the indicator will flash to indicate. Step 4: Add more receivers and remotes to the hub as you would like, refer to the corresponding remote manual. Step 5: Touchlink the added receivers and the remotes.
6. झिग्बी ग्रीन पॉवर स्विच शिकणे
पायरी १: लर्निंग मोड सुरू करण्यासाठी "रीसेट" बटण ४ वेळा दाबा. पायरी २: ग्रीन पॉवर स्विच लर्निंग मोडमध्ये सेट करा, कृपया त्याच्या मॅन्युअलचा संदर्भ घ्या. पायरी ३: यशस्वी शिक्षणासाठी स्विचवर संकेत असेल.
Note: There are two control situations: 1) Only one receiver, to be controlled by multiple GP switches: directly perform pairing between the GP switch and the receiver.
2) Only one GP switch, to control multiple receivers, or multiple GP switches and multiple receivers with crosscontrol: use one receiver as the Zigbee hub, add all other receivers to the hub, and then pair the GP switch with the receiver. The steps are as follows: Step 1: Use one receiver as the Zigbee hub and short press “Reset” button 4 times to start adding Zigbee devices. Step 2: Reset power of another receiver once to enter Zigbee network pairing mode, it will be added by the hub and the connected light will flash. Step 3: Add more receivers to the hub as you would like. Step 4: Pair the added receivers with the GP switches.
Wiring Diagram Notes for the diagrams: L – terminal for live lead N – terminal for neutral lead L-out – output terminal of the relay (controlling connected light source) S – terminal for switch
External switch type: there are 2 versions of firmware available, one is working with push switch, the other is working with toggle on/off switch, please confirm the external switch type when place the order.
1) Wiring with neutral wire
2): Wiring without neutral wire
Reset Manual
एल-आउट
S
L
N
Reset Manual
एल-आउट
S
L
N
Reset Manual
एल-आउट
S
L
N
S
S
बायपास
S
N
N
N
L
L
L
* When using the device without neutral wire, the smart relay requires at least 3W @ 240 VAC of power consumption to operate. If the connected light has a smaller power consumption, then Bypass is needed for the device to work.
कागदपत्रे / संसाधने
 |
sunricher SR-MT9041A-R ZigBee Dual Tech Smart Relay Module [pdf] सूचना पुस्तिका SR-MT9041A-R ZigBee Dual Tech Smart Relay Module, SR-MT9041A-R, ZigBee Dual Tech Smart Relay Module, Dual Tech Smart Relay Module, Tech Smart Relay Module, Smart Relay Module, Relay Module |