Stem Aria Linear Light

खबरदारी

स्थापनेपूर्वी

Please read the provided step-by-step instructions thoroughly before proceeding with the installation. You will achieve a secure and successful installation by taking these precautions and diligently following the provided guidelines.

1. कोणतेही इंस्टॉलेशन काम सुरू करण्यापूर्वी सर्किटला वीज पुरवठा बंद करण्याचे नेहमी लक्षात ठेवा. इलेक्ट्रिकल इन्स्टॉलेशनची कामे केवळ अधिकृत इलेक्ट्रिकल कॉन्ट्रॅक्टरनेच केली पाहिजेत. व्यावसायिक मार्गदर्शनासाठी, कृपया तुमच्या स्थानिक विद्युत प्राधिकरणाशी संपर्क साधा.
2. स्थापनेपूर्वी, लपविलेल्या वायरिंगचे नुकसान टाळण्यासाठी इतर कोणत्याही केबल्सच्या उपस्थितीसाठी प्रतिष्ठापन क्षेत्र तपासा.
3. When positioning the light fixture, ensure that the chosen area can adequately support the weight of light up to 3kg ( 6.6 lbs, aluminium)/ 7kg (15.4 lbs, brass).
4. कृपया लक्षात घ्या की हे मिश्रण केवळ कोरड्या घरगुती घरातील वातावरणात वापरण्यासाठी डिझाइन केलेले आहे.
5. When handling the metal fixture, make sure your hands are clean. It is advised to wear gloves to prevent leaving marks on the metal surface.
6. Periodically check screws and connections for stability. Gently tighten if necessary, avoid over-tightening.

काळजी सूचना

फिंगरप्रिंटचे कोणतेही ठसे राहू नयेत यासाठी धातूच्या पृष्ठभागाला स्पर्श करण्यापूर्वी तुमचे हात स्वच्छ असल्याची खात्री करा. प्रकाश व्यवस्था हाताळताना हातमोजे वापरण्याचा सल्ला दिला जातो. उत्पादनावर कोणतेही अपघर्षक पदार्थ वापरू नका. कृपया त्याच्या वजनापासून सावध रहा. काळजीपूर्वक हाताळा.

Over time, the metal surface may diminish its original luster. To retain the original aluminium or brass finish, use metal polish with a soft, dry cloth and gently rub it onto the surface.

तांत्रिक तपशील

• परिमाण
  • Dia.. 26 L1440 MM
  • Dia 1 L56.7 IN (Custom length on request)
• साहित्य आणि वजन
  • Cast Aluminium – 2.5 kg
  • Cast Brass – 6 kg
• केल्विन रेटिंग २७०० हजार
• प्रकाश स्रोत
  IND/ UK/ EU LED strip (Incl.)12W, 220-240V
• Classification IP20
• Dimmable Phase cut, TRIAC compatible
• हार्डवेअर
  W56 H32 D140 MM W2.2 H1.3 D5.5 IN Aluminium, Brass finish
• दोरखंड
  • हार्डवायर
  • Cord length – 2000 MM

बॉक्सच्या आत

* Driver and LED light are not included for regions with a voltage requirement of 110-120V.

(चित्र 1)

पायरी 1

Position and drill

Carefully mark the position where you intend for the light fixture to hang. Use the dimensions marked (Fig. 1) as a guide to drill holes in the ceiling, then proceed to the next step.

(चित्र 2)

पायरी 2

Install the Clutch wire gripper and Canopy back plate

1. Connect the clutch wire gripper (A1) and canopy back plate (B) by fastening them at the drilled holes in the ceiling using the drywall screws (Fig. 3).
2. Insert the clutch wire (C) through the clutch wire screw (D)(Fig. 4), fitted on the ends of the cast Rod.
3. Secure the opposite end of the clutch wire gripper (A1)(Fig. 3).
   1. To ensure the safe suspension of the light fixture, check that the wires are firmly attached to the clutch wire grippers and are devoid of any slack.

(चित्र 5)

पायरी 3

Install the second Clutch wire gripper

Take the second clutch wire gripper (A2) and fasten it directly onto the ceiling (Fig. 6) using the drywall screw. Now insert the clutch wire (C) through the clutch wire screw (D) (Fig. 4) and securely attach it to the clutch wire gripper (A2) (Fig. 6).

(चित्र 7)

पायरी 4

Install and level the Rod

Fasten the clutch wire screw (D) to both ends of the Rod (Fig. 7) and adjust its height as desired. Ensure that the light fixture is in alignment with the floor.

(चित्र 8)

पायरी 5

Connect the wiring to the driver

1. Insert the LED cord end (F) on the Rod through the hole in the canopy casing (E) and connect it to the driver output mounted on the ceiling (Fig. 8).
2. Connect the driver input to the electrical connection in the ceiling (Fig. 9).
   Ensure that all connections are secure and that there are no exposed wires or electrical hazards. Pay attention to the polarity of the connection. A wrong connection can cause damage.

(चित्र 10)

पायरी 6

Close the Canopy casing

After completing the installation, take the canopy’s top cover and attach it to the back plate (Fig. 10) using the canopy screws (Fig. 11). Ensure that the wiring and any excess clutch wire strands are neatly trimmed after the installation.

In case you require further assistance, please write to us at info@stemdesign.co.

वारंवार विचारले जाणारे प्रश्न

Can the fixture be used outdoors?

No, the fixture is designed for use in dry domestic indoor environments only.

बॉक्समध्ये काय समाविष्ट आहे?

The box includes light source, hardware, cord, wall plugs, drywall screws, clutch wire gripper, clutch wire, gloves, canopy casing with driver, rod with LED light, and clutch wire screws.

Is the driver and LED light included for all regions?

Driver and LED light are not included for regions with voltage requirement of 110-120V.

कागदपत्रे / संसाधने

stem Aria Linear Light [pdf] सूचना पुस्तिका Aria Linear Light, Linear Light, Light

संदर्भ

• वापरकर्ता मॅन्युअल