Nice RC200 Receiver
उत्पादन तपशील
- वारंवारता: 433.92 मेगाहर्ट्झ
- Maximum Output Power: Up to 500W
- Standby Power Consumption: Non
- Activation Time: Approximately 300 ms
- Memorization Capacity: Up to 30 transmitters
चेतावणी
पायरी 1
- Before proceeding with the installation, make sure the product is suit-able for its intended use. Pay special attention to the data provided in the “Technical Characteristics” chapter. NICE disclaims liability for any dam-age resulting from uses of the product other than those described in this manual.
- Protect the product’s internal components from contact with water and other polluting substances. Keep it away from heat sources and do not expose it to open flames. If any of these conditions occur, stop using it immediately and call NICE customer service.
- Disconnect the power supply before proceeding with the installation operations.
- पॅकेजिंग साहित्याची विल्हेवाट स्थानिक पातळीवर लागू असलेल्या नियमांचे पालन करून लावावी.
PRODUCT DESCRIPTION AND APPLICATIONS
पायरी 2
The RC200 radio receiver, used in combination with the ECCO5… and STX100 transmitters, is suitable for the remote control of single-phase equipment powered by the mains voltage, with up to 500W power.
The possible commands are On/Off, “Man Present”, Timer 1 and Timer 2. The radio receiver operates at a frequency of 433.92 MHz and can memorize up to 30 ECCO5… and STX100 transmitters.
इन्स्टॉलेशन
To connect the RC200 radio receiver, the normal power cable to the equipment to be controlled must be “interrupted” (Fig. 1).
WARNING: Electrical systems must be set up by qualified and experienced personnel in compliance with current legislation. As the cable clamps do not provide protection against pulling and the removable cable cap can be separated, the RC200 container must be positioned where it is inaccessible to the general public. Said container does not guarantee protection against access to those parts of the system which are live. If the RC200 radio receiver is installed outdoors, keep in mind that the cable holders are waterproof only for round cables with a diameter of 6.5 to 8.5 mm.
- व्हॉल्यूम नाही याची खात्री कराtage anywhere in the electrical circuits.
- Cut the power cable to the equipment to be controlled.
- Open the RC200 enclosure and remove the “cable holding cap” (Fig. 2).
- Strip the sheath off the two ends of the cable approx. 3 cm, then strip the single conductors approx. 5 mm.
- Thread the two cables through the holes in the cable holding “cap” (Fig. 3).
- Pull the board out a few centimetres (Fig. 4).
- Connect the conductors to the terminals (Fig. 5).
- Fold the conductors (Fig. 6).
- Push the board back inside the enclosure, making sure that the stripped sections of cable are not exposed, then slide the “cap” along the cables until the enclosure is closed tight.
- The RC200 radio receiver does not require mounting, it can be positioned directly in the dedicated compartment. To avoid any risk of water infiltrations, we recommend positioning it with the cables facing down (Fig. 7).
चेतावणी: The enclosure must not be perforated for any reason.
इलेक्ट्रिकल कनेक्शन्स
पायरी 4
वीज पुरवठा
- Use terminals 5-6-7 for the main power supply to the radio receiver (ground, phase, neutral), as shown in figure alongside “Electrical Connections”.
- Connection to the Equipment to Be Controlled
- The equipment to be controlled (Max 500W) must be connected to terminals 1-2; No. 3 is the ground terminal.
चेतावणी
- Terminal 7 (Neutral) is directly connected to terminal 1 of the equipment to be controlled, which is therefore not completely isolated from the power supply line.
- Carefully follow all the connection instructions. If you have any doubts do NOT make experiments but refer to the relevant technical specifications.
- Improper connection may cause serious damage to the radio receiver.
MEMORIZATION OF RADIO TRANSMITTERS
पायरी 5
A memorization procedure must be executed in order to enable the transmitter to control the radio receiver.
चेतावणी:
- All the memorization sequences described in this chapter are timed, there-fore they must be performed within the set time limits.
- All the receivers that are within the range of the transmitter can be memorized via radio; it is therefore expedient to power only the radio receiver involved in the operation.
You can check whether any transmitters have been previously memorized in the radio receiver; this is done by counting the number of beeps emitted when the radio receiver is switched on.
| Checking the memorized transmitters | ||
| 3 लहान बीप |  |
Some transmitters are already memorised |
| 2 लांब बीप |  |
Empty memory (no memorized transmitters) |
Two different procedures can be followed to memorize the transmitters:
- Mode 1: simplified memorization (the transmitter keys are automatically configured by the RC200 radio receiver).
- Mode 2: advanced memorization (each single transmitter key can be con-figured for a specific command).
Mode 1 (simplified memorization)
In this mode the functions of the transmitter keys are pre-set. The keys are associated by pairs: keys 1 and 2 can perform the On-Off commands from an RC200 radio receiver, whereas keys 3 and 4 can perform the On-Off commands from a different RC200 radio receiver, as shown in the example below. When the memory is empty (no memorized transmitters) you can proceed to program the first transmitter in Mode 1 as shown in table [A].
चेतावणी: if you press key 1 or 2, this pair of keys will be me morized, whereas if you press key 3 or 4, this latter pair of keys will be memorized.
If the radio receiver has already memorized one or more transmitters, when it is switched on you will hear 3 short beeps. In this case you will not be able to proceed as described above, but will have to switch to the memorization mode described in Table [B]
| Example of memorization in Mode 1 | ||
| की १ | On on RC200 no. 1 | |
| की १ | Off on RC200 no. 1 | |
| की १ | On on RC200 no. 2 | |
| की १ | Off on RC200 no. 2 | |
Even if one or more transmitters have already been memorized in Mode 1, additional transmitters can be memorized in Mode 1, as described in Table [B].
| Table [B] | Memorizing additional transmitters in Mode 1 | Example |
| 1 | Press and hold down one of the keys in the desired pair (1-2 or 3-4) on the new transmitter to be memorized (New TX) until you hear a beep (after approx. 5 seconds), then release the key |  |
| 2 | Slowly press one of the keys in the desired pair on a previously memorized transmitter (old TX) |  |
| 3 | Once again, press and release the key on the new transmitter you pressed according to step 1 |  |
| The 3 final beeps signal that the new transmitter has been correctly memorized. If the memory is full (30 transmitters), 6 beeps will signal that the memory is not capable of memorizing any additional transmitters. | ||
Mode 2 (advanced memorization)
In this mode, each of the 4 available commands can be associated to a transmitter key, as shown in Table [C].
| Table [C] | Commands available for memorization Mode 2 | |
| N° | आज्ञा | वर्णन |
| 1 | ऑन-ऑफ | The first command switches on the unit, the next one switches it off, and so on |
| 2 | माणूस उपस्थित | When the key is pressed the relay contact closes. When the key is released the relay contact opens |
| 3 | टाइमर 1 | The contact remains closed for a length of time ranging from 1 sec to 9 hours (programmable as shown in Table [G]) |
| 4 | टाइमर 2 | The contact remains closed for a length of time ranging from 1 sec to 9 hours (programmable as shown in Table [G]) |
In this mode, the memorization procedure is performed separately for each single transmitter key; this means that 2 keys on the same transmitter can be memorized for two commands to the same radio receiver, or to command different receivers as illustrated in the exampखाली:
| Example of memorization in Mode 2 | ||||
| की १ | On-Off on RC200 no. 1 | |||
| की १ | Timer1 on RC200 no. 2 | |||
| की १ | Timer2 on RC200 no. 3 | |||
| की १ | Man Present on RC200 no. 3 | |||
To memorize the transmitters in Mode 2, refer to Tables [D] and [E].
| Table [D] | Memorizing the first transmitter in Mode 2 | Example |
| 1 | As soon as the radio receiver is powered
you will hear 2 long beeps |
|
| 2 | Within 5 seconds, press the desired key on the transmitter to be memorized and hold it down until al 3 beeps have sounded, then release the key |
|
| 3 | Within 3 seconds, press the same key on the transmitter as many times as the number corresponding to the desired command: 1 = On-Off; 2 = Man Present; 3 = Timer1; 4 = Timer2 |
|
| 4 | After approx. 3 seconds you will hear a number of beeps corresponding to the selected command |  |
| 5 | Within 2 seconds, press and release the
same key to confirm the programming |
 |
| The 3 final beeps signal that the new transmitter has been correctly memorized. During step 4, if you do not hear the number of beeps corresponding to the desired function, wait 10 seconds before abandoning the procedure, then try again. | ||
The 3 final beeps signal that the new transmitter has been correctly memorized. If the memory is full (30 transmitters), 6 beeps will signal that the transmitter cannot be memorized.
Memorizing a new transmitter like a previously memorized transmitter
It is possible to memorize a new transmitter so that it operates exactly like a previously memorized one. If the old transmitter was memorized in Mode 1, the new one will also operate in Mode 1 and a single memorization stage will be required. If the key on the old transmitter was memorized in Mode 2, also the key on the new transmitter will be memorized in Mode 2 and will perform the same function. If you wish to memorize more than one key you will have to perform a memorization procedure for each key.
The 3 final beeps signal that the new transmitter has been correctly memorized. If the memory is full (30 transmitters), 6 beeps will signal that the memory is not capable of memorizing any additional transmitters.
Programming the Timers
- The RC200 radio receiver features two independent timers (Timer1 and Tim-er2) for automatic relay deactivation after a set time delay.
- The deactivation time can be brought forward, compared to the timer setting, by maintaining the “timer” command active for more than 3 seconds or by giving an “Off” command.
- The factory or default settings for the two timers are 1 minute (Timer1) and 10 minutes (Timer2) respectively.
- The time settings can be programmed separately for each of the two timers, from a minimum of 1 second to a maximum of 9 hours. Once the timer has been programmed, every command associated with it will activate the relay for the set time interval.
- In order to program the timers you need to have a transmitter memorized for timer control, then follow the steps in the table [G].
3 long beeps will signal that the time has been programmed successfully; the following 1 or 2 short beeps indicate whether timer1 or timer2 has been programmed.
Clearing the Receiver Memory
There may be cases when the RC200 radio receiver memory has to be cleared. The memory can be cleared using:
- non-memorised transmitters or those which have been memorised for “Timer” commands starting from point A.
- A previously memorized transmitter, starting from step N. 1
The following items may be erased:
- Transmitters only, proceeding up to step 4
- All the data (transmitters and timers), completing the procedure up to step 5.
| ➨ 1 | • With the transmitter in Mode 1 or not memorized:Press and hold down key 2 or key 4 on a transmitter previously memorized in Mode 1 until you hear a beep (after approx. 5 seconds), then release it.• With the transmitter in Mode 2 (On/ Off or timer only):For On/Off with open relay (Off), press the key to activate it (On), release the key, press it again and hold it down until you hear a beep (after approx. 5 seconds), then release the key.For timer with open relay (Off), press the key to activate the relay (On), hold down the key until the relay is deactivated (Off) and you hear a beep (after approx. 5 seconds), then release the key |  |
| 2 | After 1 second, press the same key again and release it precisely during the third beep |  |
| 3 | After 1 second, press the same key again and release it precisely during the third beep |  |
| ➨ 4 | After 1 second, press the same key again and release it precisely during the third beep |  |
| ➨ 5 | If you wish to completely erase all the data stored in the memory, press the key again within 2 seconds and then release it After a few seconds, 5 beeps will signal that the memory has been cleared |  |
देखभाल आणि विल्हेवाट
पायरी 6
The system does not require special maintenance.
This product is made of various materials; some may be recycled and others must be disposed of. Obtain information on product recycling or disposal, in observance of current local standards.
Caution: come electronic components may contain pollutant substances; never dispose of into the environment.
तांत्रिक वैशिष्ट्ये
| RC200 Radio receiver | |
| प्रकार | radio receiver for control of general electrical equipment |
| तंत्रज्ञान स्वीकारले | reception and decoding of the radio signals emitted by the transmitters activation of the output relays only in case of correspondence with a previ- ously memorized code, correctly syn- chronized with the variability sequence |
| रिमोट कंट्रोलची शक्यता | with ECCO5… or STX100 transmitters |
| कोडिंग | 64 bit rolling code (18 billion billion combinations) |
| ECCO5… and STX100 transmitters memorization capacity | up to 30, if memorized in Mode 1 |
| रिसेप्शन वारंवारता | 433.92 MHz |
| प्राप्तकर्ता संवेदनशीलता | better than 0.6µV (with direct coupling) |
| Range of ECCO5… and STX100 transmitters | estimated at 50-100m (this distance may vary in the presence of obstacles or electromagnetic disturbances) |
| वीज पुरवठा | 230Vac (+10-15%) 50Hz |
| जास्तीत जास्त उर्जा उत्पादन | 500W / 400VA |
| Absorption when idle | < 0.7W (typical at 230 Vac) |
| सक्रिय करण्याची वेळ | अंदाजे 300ms |
| निष्क्रियीकरण वेळ | अंदाजे 300ms |
| Maintenance of output status in case of power failure | नाही |
| Timer resolution and precision | 1s/±2% |
| ऑपरेटिंग सभोवतालचे तापमान | -10 डिग्री सेल्सियस… + 55 डिग्री सेल्सियस |
| संरक्षण वर्ग | IP55 (enclosure undamaged) with round cables having a diameter of 6.5 to 8.5 mm |
| परिमाणे / वजन | 98 x 26 x 20 / 45 g |
CE अनुरूपतेची घोषणा
निर्देश १९९९/५/EC नुसार घोषणापत्र
Note: The contents of this declaration correspond to declarations in the official document deposited at the registered offices of Nice S.p.A. and in particular to the last revision available before printing this manual. The text herein has been re-edited for editorial purposes. A copy of the original declaration can be requested from Nice S.p.A. (TV) Italy.
- Declaration number: 584/RC
- पुनरावृत्ती: ०.०१
- भाषा: EN
The undersigned, Roberto Griffa, in the role of Chief Executive Officer, declares under his sole responsibility, that the product:
- Manufacturer’s Name: NICE S.p.A.
- पत्ता: Pezza Alta 13 मार्गे, 31046 Rustignè di Oderzo (TV) Italy
- Model: RC200 radio receiver
- ॲक्सेसरीज:
Conforms to the essential requirements stated in article 3 of the following EC directive, for the intended use of products:
- DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity, in accordance with the following harmonised standards:
- Health and safety (Art. 3(1)(a)): EN 62479:2010
- Electrical safety (Art. 3(1)(a)): EN 60950-1:2006+A11:2009+A12:2011+A1:20 10+A2:2013
- Electromagnetic compatibility (Art. 3(1)(b)): EN 301 489-1 V1.9.2:2011, EN 301 489-3 V1.6.1:2013
- Radio spectrum (Art. 3(2)): EN 300 220-2 V2.4.1:2012
ओडेरझो, २८ जुलै २०१६ 
वारंवार विचारले जाणारे प्रश्न
How many transmitters can the RC200 radio receiver memorize?
The RC200 radio receiver can memorize up to 30 ECCO5 and STX100 transmitters.
What are the possible commands that can be programmed with the RC200?
The possible commands are On/Off, Man Present, Timer 1, and Timer 2.
What is the frequency at which the radio receiver operates?
The radio receiver operates at a frequency of 433.92 MHz.
कागदपत्रे / संसाधने
 |
Nice RC200 Receiver [pdf] सूचना STX100, ECCO5, RC200 Receiver, RC200, Receiver |