MODECOM STELLAR PLUS 8F ARGB Midi Computer Cases

तपशील

• Form Factor Supported: Mini-ITX, Micro-ATX, ATX
• Max PSU Length: 230 mm
• Max GPU Length: 420 mm
• Max CPU Cooler Height: 175 mm

पॅनेल I/O

1. पॉवर
2. USB 3.0
3. USB 3.0
4. यूएसबी-सी
5. HD AUDIO 6 RESET / LED

ॲक्सेसरीज

• A HDD SCREWS
• B MOTHERBOARD & SSD SCREWS
• C PSU AND GPU SCREWS
• D RISER CABLE STANDOFFS
• E ZIP TIE
• F SCREWDRIVER
• G CLOTH
• H TG PANEL CLIP
• I SSD SILICONE PADS
• J MB STANDOFFS
• K VELCRO STRAPS
• L SSD SCREWS
• M SCREWS FOR INSTALLING FANS ON A WATER COOLING

ओव्हरview

स्थापना

3.5” HDD इंस्टॉलेशन

२.५” एसएसडी इंस्टॉलेशन

Connecting the case plugs

The plugs should be connected to the motherboard according to the instructions included with the motherboard.

GPU क्षैतिज स्थापना

GPU वर्टिकल इंस्टॉलेशन

वीज पुरवठा स्थापना

Long Power Supply Instalation

परिमाण

मदरबोर्ड स्थापना

ARGB hub connection

PRE-INSTALLED: STELLAR PLUS 5F & STELLAR PLUS 8F

कार्य

1. LED मोड मधून सायकल चालवण्यासाठी LED बटण लहान दाबा.
2. मदरबोर्ड कंट्रोलमध्ये मोड बदलण्यासाठी 3 सेकंदांसाठी LED बटण दाबा.
3. LED पॉवर बंद करण्यासाठी LED बटण 5 सेकंद दाबा.
4. मॅन्युअल कंट्रोलवर परत जाण्यासाठी LED बटण दाबा.
5. Memory function after power off.
   (FOR A MOTHERBOARD EQUIPPED WITH ARGB FAN CONTROL CONNECTORS, CONNECT IT TO LED CONTROL CONNECTOR ON MB) CONNECT POWER SUPPLY TO SATA. CONNECT LED SW.

Information on Connecting PWM Fans to the Motherboard

• Before connecting PWM fans, it is recommended to check the mother-board manual for the maximum allowable current for the (SYS_FAN) PWM headers.
• If your motherboard supports a load of up to 3 A on a single (SYS_FAN) PWM header, all fans can be connected in a daisy-chain configuration to one header, as prepared by the manufacturer.
• If the allowable current is lower — for example, 1 A per (SYS_FAN) PWM header — the fan cables from the case should be split into several groups (up to three fans per group), with each group connected to a separate (SYS_FAN) PWM header on the motherboard.
• Note: Exceeding the maximum load of a (SYS_FAN) PWM header may result in issues such as the system failing to power on.

द्रुत प्रारंभ मार्गदर्शक/स्थापना

1. Open the Computer Case: Carefully remove the side panel of the computer case to access the internal compartment.
2. Install Internal Components: Install all necessary computer components (e.g., motherboard, CPU, RAM, GPU, storage devices) in accordance with the manu-facturer’s individual assembly instructions for each component.
3. Install and Connect the Power Supply Unit (PSU): Mount the power supply in the designated location as illustrated in this manual. Connect the PSU cables to the appropriate components, following both the PSU’s installation guide and the connection requirements of each component.
4. Verify Assembly: Ensure all components are securely installed and that all power and data cables are properly connected.
5. Close the Case: Reattach the side panel to close the computer case.
6. Connect Peripherals: Attach the monitor, keyboard, mouse, and any other necessary peripherals to the appropriate ports on the computer.
7. Connect to Power: Plug the power cord into the PSU socket and then into a 230V AC wall outlet.
8. Power On: If your PSU has a power switch, set it to the ‘I’ (on) position to enable power.

This device was designed and made of high-quality reusable materials and components. If the device, its packaging, user’s manual, etc. are marked with crossed waste container, it means they are subject to segregated household waste collection in compliance with the Directive 2012/19/UE of the European Parliament and of the Council. This marking informs that electric and electronic equipment shall not be thrown away together with household waste after it’s been utilised. The user is obliged to bring the utilised equipment to electric and electronic waste collection point. Those running such collection points, including local collection points, shops or commune units, provide convenient system enabling to scrap such equipment. Appropriate waste management aids in avoiding consequences which are harmful for people and the nvironment and result from dangerous materials used in the device, as well as improper storage and processing. Segregation household waste collection aids recycle materials and components of which the device was made. A household plays crucial role in contributing to recycling and reusing the waste equipment. This is the stage where the basics are shaped which largely influence the environment being our common good. Households are also one of the biggest users of small electrical equip-ment. Reasonable management at this stage aids and favours recycling. In the case of improper waste management, fixed penalties may be imposed in accor-dance with national legal regulations.

संगणक केस सुरक्षा सूचना

1. परिचय
   आमचा संगणक केस निवडल्याबद्दल धन्यवाद. तुमच्या सुरक्षिततेची आणि उपकरणाच्या योग्य ऑपरेशनची खात्री करण्यासाठी, कृपया हे मॅन्युअल काळजीपूर्वक वाचा. या सूचनांचे पालन केल्याने तुमच्या उपकरणांना होणारे संभाव्य धोके आणि नुकसान टाळण्यास मदत होईल.
2. सुरक्षितता चेतावणी आणि सावधगिरी
   1. स्थापना आणि ऑपरेशन
      1. संगणक चालू असताना तो कधीही उघडू नका. इंस्टॉलेशन किंवा देखभाल सुरू करण्यापूर्वी, संगणक अनप्लग केलेला असल्याची खात्री करा.
      2. Do not use the case in a humid environment. Moisture can cause short circuits and damage to com-ponents.
      3. केसच्या आतील तीक्ष्ण कडांपासून सावधगिरी बाळगा. दुखापत टाळण्यासाठी घटक बसवताना संरक्षक हातमोजे घाला.
      4. माउंटिंग स्क्रू घट्ट केले आहेत याची खात्री करा, पण जास्त घट्ट केलेले नाहीत. जास्त घट्ट केल्याने धागे खराब होऊ शकतात.
   2. वीज पुरवठा
      1. Only use power supplies that are compatible with the case. An incorrect power supply can cause over-heating or short circuits.
      2. Check for correct wiring. Incorrectly connected ca-bles can damage components and the case.
      3. Do not load multiple devices on the same electrical circuit. Ensure adequate power stability to avoid over-loading the electrical network.
   3. वायुवीजन आणि अतिउष्णता
      • पुरेसा हवा प्रवाह सुनिश्चित करा. व्हेंट्स किंवा फिल्टर्स ब्लॉक करू नका. धूळ फिल्टर्स नियमितपणे स्वच्छ करा.
      • Do not install the case in an enclosed space with-out air circulation. Avoid placing the computer near heat sources such as radiators.
      • Monitor component temperatures. If you are using high-performance components, consider installing addi-tional fans or a liquid cooling system.
   4. स्टोरेज आणि वाहतूक
      • Store the case in a dry and clean place. Avoid expo-sure to extreme temperatures, moisture, and dust.
      • Protect the case from shocks during transporta-tion. Use the original packaging or appropriate protec-tive materials.
3. विधानसभा सूचना
   1. विधानसभेची तयारी
      • तुमच्याकडे सर्व आवश्यक साधने आहेत याची खात्री करा (उदा. फिलिप्स स्क्रूड्रायव्हर).
      • प्रकाशाची सोय आणि पुरेशी कामाची जागा असलेले योग्य कामाचे क्षेत्र निवडा.
   2. घटक स्थापित करणे
      • शॉर्ट सर्किट टाळण्यासाठी माउंटिंग स्पेसरवर मदरबोर्ड स्थापित करा.
      • सीपीयू, रॅम आणि ग्राफिक्स कार्ड स्थापित करताना उत्पादकाच्या सूचनांचे पालन करा.
      • मदरबोर्ड आणि पॉवर सप्लायवरील लेबलांनुसार केबल्स जोडा.
      • सर्व घटक योग्यरित्या जोडलेले आहेत आणि कोणत्याही केबल्समुळे पंखे ब्लॉक होत नाहीत याची खात्री करा.
4. स्वच्छता आणि देखभाल
   1. कॉम्प्रेस्ड एअर वापरून केसच्या आतील धूळ नियमितपणे काढा.
   2. धूळ फिल्टरची स्थिती तपासा आणि दर काही आठवड्यांनी ते स्वच्छ करा.
   3. केसमध्ये कोणतेही द्रव साफ करणारे एजंट वापरू नका.
5. अतिरिक्त माहिती
   • Warranty: To avoid voiding the warranty, do not modify the case or its components.
   • Technical Support: In case of problems, contact our customer service department.
   • Recycling: Dispose of used devices at appropriate recycling points in accordance with local regulations.
     या मार्गदर्शक तत्त्वांचे पालन केल्याबद्दल धन्यवाद. केसचा योग्य वापर तुमच्या उपकरणाची सुरक्षितता आणि दीर्घायुष्य सुनिश्चित करेल.

वारंवार विचारले जाणारे प्रश्न

Q: What should I do if my motherboard does not support the recommended current for PWM headers?

A: If your motherboard does not support the recommended current for PWM headers, split the fan cables into smaller groups and connect them to separate PWM headers to avoid exceeding the maximum load per header.

Q: How do I troubleshoot issues related to system power-on failures?

A: Check the maximum allowable current for PWM headers in your motherboard manual. Exceeding this limit may result in system power-on issues. Ensure proper fan connections and distribution to avoid overloading a single PWM header.

कागदपत्रे / संसाधने

MODECOM STELLAR PLUS 8F ARGB Midi Computer Cases [pdf] स्थापना मार्गदर्शक STELLAR PLUS 8F, STELLAR PLUS 8F ARGB Midi Computer Cases, ARGB Midi Computer Cases, Midi Computer Cases, Computer Cases

संदर्भ

• वापरकर्ता मॅन्युअल