MiBOXER SPIW5 5in1 SPI plus DMX LED Controller

उत्पादन वैशिष्ट्य

• Support 2.4GHz wireless transmitting technology
• 5 in 1 SPI controller, single color, cct, rgb, rgbw, rgb+cct output selection
• Speed, static mode, dynamic mode, and music mode are adjustable
• compatible with DC5-24V input
• Dynamic mode: 28 kinds of white color and 80 kinds of RGB color for selection, it can change color, brightness, width, and speed for those modes
• 8 kinds of music modes work with the internal microphone and smart smartphone microphone
• Freely switching between dynamic mode and music mode
• Have DND mode, usually used in a power failure area to save power

उत्पादन पॅरामीटर

• उत्पादनाचे नाव: 5 in 1 SPI LED Controller (2.4G）
• मॉडेल क्र.: SPIR5
• इनपुट व्हॉल्यूमtage: DC 5V-24V
• आउटपुट वर्तमान: कमाल 10A
• आउटपुट सिग्नल: SPI(TTL) 800Kbps (Max 1024 Pixel)
• स्टँडबाय वर्तमान: 20mA
• प्रोटोकॉल: WiFi+RF 2.4GHz
• नियंत्रण अंतर: 30 मी
• आयपी दर: IP20
• कार्यरत तापमान.:-10~40℃|
• परिमाण: 74.5*36*17 मिमी
• EMC Standard (EMC)：ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4
• सुरक्षा मानक (LVD): EN 62368-1; 2020+A11;2020
• रेडिओ उपकरणे (RED): ETSI EN 300 440 V2.2.1
• प्रमाणन: CE, EMC, LVD, RED

कनेक्शन आकृती

संकेत

When used in conjunction with the C9/B9 remote control, the following functions can be achieved

Compatible remote ( purchase separately)

Static Mode Button：
Switch pure static lighting

Dynamic Mode Button:
Short-press to switch dynamic mode

संगीत मोड बटण:

• Short-press to switch music mode
• अंतर्गत संगीत मोड: You must press the music mode button one more time if you want to do another operation

दृश्ये बटण:

• Only work for dynamic and music mode, short-press to get scenes
• Long-press to save the current scene while the light is under dynamic mode

लॉक बटण:
Remote is locked automatically without any operation within 15 seconds. Short-press 1 time to unlock it Long-press press “Lock” button 3 seconds to shut it down

RGB slider:
Touching to dim RGB

Pixel points slider:
Touching to set length and width ( checking more details from the following instruction)

Speed slider:
Touching to set speed

ब्राइटनेस स्लाइडर:
Touching to dim under music mode: it can adjust the sensitivity of the microphone chip

लिंक/अनलिंक

दुवा

1. Power off 10 seconds and power on again or short-press “SET”
2. Press the ” ON” button 3 times within 3 seconds.
3. Green flashing state, then the code is successful.

• Link is failed if the light doesn’t flash, please repeat the above steps
• （Attention: can not link again if remote already finished linking）

अनलिंक करा

1. Power off 10 seconds and power on again or short-press “SET”
2. Press the “ON” button 5 times within 3 seconds.
3. Red flashing state, then clear the code successfully.

• Unlink is failed if light doesn’t flash, please repeat the above steps
• (लक्ष: no need to unlink if the light is never be linked）

सेटिंग

1.  Setting the color sequence from strip light
   Long-press “OFF” 5 seconds until it lights up single color
2. लांबी सेट करणे
   （Pixel number: mini 8pt, max 1024pt）
3. Setting the width for dynamic mode
   Long press “ON” 5 seconds until it lights up white color and the last point is blinkingSliding the pixel number to change the pt number and get a different length for the dynamic mode, which has various sections.
4. Setting time and color for ON/OFFSliding “Speed” to set time for ON/OFF
   Sliding “RGB” to set the color for ON/OFF
   Short-press “ON/OFF” to leave out once the setting is done
5. Turn Do Not Disturb mode on and off (ON by default)
   “व्यत्यय आणू नका” चालू करा (वारंवार वीज असलेल्या भागात लागूtagऊर्जा वाचवण्यासाठी es)

डू नॉट डिस्टर्ब मोड चालू करा:
Short-press the “OFF” button 3 times within 3 seconds, and then short-press the “ON” button 3 times. The light flashes 4 times to indicate success.

टीप: जेव्हा एलamp पॉवर ou नंतर पुन्हा चालू आहेtage, its status (lights on or off) will remain the same as before the power outage.

डू नॉट डिस्टर्ब मोड बंद करा:
Short-press the “ON” button 3 times within 3 seconds, and then short-press the “OFF” button 3 times. The light flashes 4 times slowly to indicate a successful shutdown.

टीप: जेव्हा एलamp पॉवर ou नंतर पुन्हा चालू आहेtagई, त्याची स्थिती डीफॉल्टनुसार चालू असेल.

लक्ष द्या

1. Please turn off off power supply before installation.
2. कृपया इनपुट व्हॉल्यूमची खात्री कराtage to be same as the requirements of the device.
3. Don’t disassemble the device if you are not an expert; otherwise, it will damage it.
4. Please do not use the light in a place with a wide range of metal areas or strong electromagnetic waves nearby, otherwise, the remote distance will be seriously affected.

वारंवार विचारले जाणारे प्रश्न

How do I reset the SPI LED Controller?

To reset the SPI LED Controller, power off for 10 seconds and power on again or follow the specific reset instructions provided in the manual.

Can I use multiple SPI LED Controllers together?

Yes, you can use multiple SPI LED Controllers together by following the installation and connection guidelines.

कागदपत्रे / संसाधने

MiBOXER SPIW5 5in1 SPI plus DMX LED Controller [pdf] सूचना पुस्तिका SPIR5, SPIW5 5in1 SPI plus DMX LED Controller, SPIW5, 5in1 SPI plus DMX LED Controller, SPI plus DMX LED Controller, DMX LED Controller, LED Controller, Controller

संदर्भ

• वापरकर्ता मॅन्युअल