सामग्री लपवा
1 LUTRON MA-T51MNB मेस्ट्रो काउंटडाउन टाइमर
2 वायरिंग प्रकार निश्चित करा
3 मधले भाग काढून टाका (डिव्हायसेस गँग करत असल्यास)
4 मिश्रित लोड प्रकारांसाठी कमाल रेटिंग
5 ऑपरेशन
6 तारा डिस्कनेक्ट करा
7 समस्यानिवारण
8 कागदपत्रे / संसाधने
8.1 संदर्भ

LUTRON- लोगो

LUTRON MA-T51MNB मेस्ट्रो काउंटडाउन टाइमर

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-product

कमाल लोड रेटिंग

  • 150 डब्ल्यू एलईडी LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (1)/ सीएफएलLUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (2)
  • 450 W MLVLUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (3)
  • 600 W ELVLUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (4)
  • 600 डब्ल्यू इनकॅन्डेसेंट / हॅलोजनLUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (6)
  • 3 A FanLUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (5)
  • 5 A FluorescentLUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (2)

Maestro Timer Switch 120 V~ 50 / 60 Hz
कृपया भेट द्या www.lutron.com/ma-t51mnb साठी:

  • उपयुक्त व्हिडिओ
  • Advanced programming and operation
  • Additional wiring scenarios
  • If you have three or more switches controlling a light

कृपया स्थापित करण्यापूर्वी वाचा.

For lights and/or a fan switched from one location
(For lights and/or a fan switched from two locations, see instructions starting on page 4)

वायरिंग प्रकार निश्चित करा

For lights and/or a fan switched from two locations, see instructions starting on page 4. For lights and/or a fan switched from one location, proceed to Step 2 below.
Turn the power OFF at the circuit breaker.

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (8)चेतावणी: शॉक धोका
गंभीर दुखापत किंवा मृत्यू होऊ शकतो. सर्किट ब्रेकर किंवा फ्यूज स्थापित करण्यापूर्वी वीज बंद करा.

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (7)

Remove the existing device.e

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (9)

For lights and/or a fan switched from one location (continued)
(For lights and/or a fan switched from two locations, see instructions starting on page 4)

मधले भाग काढून टाका (डिव्हायसेस गँग करत असल्यास)

Remove the middle sections if mounting two or more devices side by side. See the Maximum Ratings chart below for the new wattage मर्यादा.
टीप: फक्त CFLs किंवा LEDs वापरताना कोणत्याही डिरेटिंगची आवश्यकता नाही.

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (10)

मिश्रित लोड प्रकारांसाठी कमाल रेटिंग

 

लोड प्रकार

 कमाल लोड
कोणत्याही बाजू काढल्या नाहीत 1 बाजू काढली 2 बाजू काढल्या
एलईडी / सीएफएल 1.25 ए / 150 प 1.25 ए / 150 प 1.25 ए / 150 प
हॅलोजन / इनॅन्डेन्सेंट 600 प 500 प 400 प
Magnetic Low-Voltage* 600 VA / 450 W 500 VA / 400 W 400 VA / 300 W
इलेक्ट्रॉनिक लो-वॉल्यूमtage 600 प 500 प 400 प
फ्लोरोसेंट २.२ अ २.२ अ २.२ अ
सामान्य Purpose Fan २.२ अ २.२ अ २.२ अ

टीप: जास्तीत जास्त एलamp वाटtage is determined by the efficiency of the transformer, with 70–85% as typical. For actual transformer efficiency, contact either the fixture or transformer manufacturer. The total VA rating of the transformer(s) shall not exceed the VA rating of the timer switch.

Connect the new timer switch (this product requires a neutral wire!)
स्क्रूभोवती तारा पूर्णपणे गुंडाळा आणि घट्ट करा (A), किंवा उष्णतारोधक तारा 1/2 इंच (13 मिमी) वर काढा आणि पुश-इन टर्मिनल्स (B) मध्ये घाला.

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (11)

For lights and/or a fan switched from one location (continued)
(For lights and/or a fan switched from two locations, see instructions starting on page 4)

Mount the timer switch using the provided screws

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (12)
Turn the power ON at the circuit breaker.r

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (13)

ऑपरेशन

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (14)

टायमर इंडिकेटर लाइट्स (TILs)

  • White TILs indicate the timer switch duration or the remaining time in minutes.
  • The top TIL labeled ON has no time limit.
  • The bottom TIL blinks rapidly to indicate 1 minute remaining (TILs are not available on the accessory switch).

महत्वाचे

  1. खबरदारी: To avoid overheating and possible damage to other equipment, do not use this to control receptacles.
  2. Install according to all national and local electrical codes.
  3. Grounding: When no “grounding means” exists in wallbox, the 2011 National Electrical Code® (NEC®) allows a control to be installed as a replacement if 1) a non-metallic, noncombustible faceplate is used with non-metallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.
  4. Maestro timer switches are not compatible with standard 3-way / 4-way switches. For use only with Maestro accessory switches (MA-AS, MSC-AS).
  5. Maestro accessory switches (MA-AS, MSC-AS) cannot be used individually and must be used in conjunction with a Maestro timer switch in a 3-way / 4-way application.
  6. In any 3-way / 4-way circuit, use only one timer switch (must be on the load side) with up to 9 accessory switches (MA-AS, MSC-AS).
  7. Operate between 32°F and 1104°F(0 °C and 40 °C), 0-90% relative humidity, non-condensing.
  8. पेंटिंग किंवा स्पॅकलिंग करताना धूळ आणि घाण पासून नियंत्रण संरक्षित करा.
  9. The timer switch may feel warm to the touch during normal operation.
  10. Recommended wallbox depth is 2.25 in (57 mm) minimum.
  11. Maximum wire length between the timer switch and the farthest accessory switch (MA-AS, MSC-AS) is 250 ft (76 m).
  12. For safety reasons, do not use the timer switch to control fixtures that are the only source of illumination for an area.
  13. For cleaning recommendations, see www.lutron.com/cleaning

For lights and/or a fan switched from two locations
(For lights and/or a fan switched from three or more locations, please visit www.lutron.com/ma-t51mnb)

सर्किट ब्रेकरवर पॉवर बंद करा
चेतावणी: शॉक हॅझार्ड.
गंभीर दुखापत किंवा मृत्यू होऊ शकतो. सर्किट ब्रेकर किंवा फ्यूज स्थापित करण्यापूर्वी वीज बंद करा.

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (15)

Remove (but do not disconnect) existing devices.

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (16)

कॉमन टर्मिनलवर वायर चिन्हांकित करा

दोन्ही विद्यमान उपकरणांवर, वायर चिन्हांकित करा (उदाample, using electrical tape) that is connected to the screw that is a different color (typically black) than all the others. This screw terminal may also be labeled “COMMON” or “COM”.
Does not include the ground screw.

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (17)

तारा डिस्कनेक्ट करा

मधले भाग काढून टाका (डिव्हायसेस गँग करत असल्यास)
तपशीलांसाठी पृष्ठ २ वरील चरण ४ पहा.

For lights and/or a fan switched from two locations (continued)
(For lights and/or a fan switched from three or more locations, please visit www.lutron.com/ma-t51mnb)

Connect the new timer switch and a Maestro accessory switch (MA-AS or MSC-AS)
टीप: The timer switch must be installed on the load side of multi-location wiring.

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (18)

स्क्रूभोवती तारा पूर्णपणे गुंडाळा आणि घट्ट करा (A), किंवा उष्णतारोधक तारा 1/2 इंच (13 मिमी) वर काढा आणि पुश-इन टर्मिनल्स (B) मध्ये घाला.

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (19)

For lights and/or a fan switched from two locations (continued)
(For lights and/or a fan switched from three or more locations, please visit www.lutron.com/ma-t51mnb)

प्रदान केलेले स्क्रू वापरून सर्व उपकरणे माउंट करा

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (20)

Turn the power ON at the circuit breaker.r

LUTRON-MA-T51MNB-Maestro-Countdown-Timer-fig- (21)

समस्यानिवारण

लक्षण संभाव्य कारण
The load does not turn ON, but the LED on the timer switch is ON. • Light bulbs are burned out.

• The timer switch is not properly wired.

• The neutral wire is not connected.

• The load was not properly installed.

• Fan not turned on at fixture.
The load does not turn ON, and the LED on the timer switch is OFF. • Timer switch is not properly wired, wires connected to brass and black screw terminals may be reversed.

• The neutral wire is not connected.

• Front Accessible Service Switch (FASS) ona  timer switch or any accessory switch is pulled out to the OFF position.

• ब्रेकर बंद आहे किंवा ट्रिप झाला आहे.
The load turns ,ON and the timer switch works, but the accessory switch does not work. • Wire connected to the blue screw terminal on timer switch is not the same wire connected to the blue screw terminal on accessory switch.

• The timer switch is not installed on the load side of the circuit.
Load does not remain ON, LED glows dimly, or blinks. • Blue screw terminal miswired to neutral wire or touching ground.

मदत करा
यूएसए | कॅनडा | कॅरिबियन 1.844.LUTRON1 (588.7661)
मेक्सिको +१.८८८.२३५.२९१०
इतर +१.६१०.२८२.३८००

मर्यादित वॉरंटी: www.lutron.com/TechnicalDocamentLibrary/369-119_Wallbox_Warranty.pdf
Lutron, the Lutron logo, and Maestro are trademarks or registered trademarks of Lutron Electronics Co., Inc., in the U.S. and/or other countries.
इतर सर्व उत्पादनांची नावे, लोगो आणि ब्रँड ही त्यांच्या संबंधित मालकांची मालमत्ता आहेत.

कागदपत्रे / संसाधने

LUTRON MA-T51MNB मेस्ट्रो काउंटडाउन टाइमर [pdf] स्थापना मार्गदर्शक
MA-T51MNB, MA-T51MNB मेस्ट्रो काउंटडाउन टाइमर, मेस्ट्रो काउंटडाउन टाइमर, काउंटडाउन टाइमर

संदर्भ

एक टिप्पणी द्या

तुमचा ईमेल पत्ता प्रकाशित केला जाणार नाही. आवश्यक फील्ड चिन्हांकित आहेत *