लाईट कंट्रोल LC-PS12802 EIBKNX बस डेटा ट्रान्सफर

उत्पादन संपलेview

The EIB/KNX bus power supply is used to provide and monitor the voltage of the EIB/KNX system. The output has two terminals, including 1 KNX bus output for EIB bus power supply and signal transmission; 1 30VDC auxiliary output, which can provide a 30VDC power supply voltage to the terminal device; the bus connection end has integrated a reactor inside the power supply; if the 30VDC auxiliary power supply end is connected to an external reactor, it can also be used as a bus power supply end, and also has a signal transmission function.

In order to facilitate installation in the distribution box, the KNX bus power supply is designed as a modular installation device that can be installed on a 35 mm DIN rail. The device uses screw terminals to realize 220VAC voltage input and auxiliary power output connection, and the EIB bus connection is directly connected through the EIB terminal (red/black).

The power supply can be reset by pressing the reset button on the device. During the reset, the bus power supply end of the power supply is powered off, and other devices connected to the bus return to their original state.

कार्यात्मक वर्णनः

1. Meet the power supply requirements of KNX/EIB bus devices;
2. With short circuit and overcurrent protection;
3. Load status indication;
4. System reset function;
5. Ripple less than 150mV

पॅरामीटर्स

इनपुट व्हॉल्यूमtage	100-240VAC
इनपुट वर्तमान	1.6A/220VAC
वारंवारता	50-60Hz
कार्यक्षमता	87%
KNX bus output	21-30V DC, 1 loop belt reactor
सहायक पॉवर आउटपुट	30V DC, 1 loop No reactor
सहायक आउटपुट वर्तमान	I1≤1280mA, Short circuit protection
सहायक आउटपुट वर्तमान	I2≤1280mA
Bus output power	≤38.4W
Auxiliary output power	≤38.4W
आउटपुट व्हॉल्यूमtage अचूकता	±5%(KNX)，±1%(AUX)
Power-off maintenance time	100ms/230VAC
ओव्हरलोड संरक्षण	2.65~3A, Hiccup protection, automatic recovery
आउटपुट ओव्हरव्होलtage संरक्षण	33~35V DC
परिमाण (Lx W x H)	145mmX90mmX64mm
शेल साहित्य	PA66
वजन (अंदाजे)	सुमारे 470 ग्रॅम
स्थापना	35mm DIN
ऑपरेटिंग तापमान	-20°C…+ 50°C
स्टोरेज तापमान	– 25°C…+ 55°C
वाहतूक तापमान	– 25°C…+70°C

Dimensional Drawings And Wiring Diagrams

परिमाण

वायरिंग

उत्पादन ऑपरेशन सूचना

1. वर्णन: 100~240VAC power connection port, wires with a diameter of 0.2-4mm2 can be connected;
2. वर्णन: Auxiliary power supply 30V DC output connection port, yellow wire connected to “+”, white wire connected to “-“;
3. वर्णन: KNX bus power supply output port, KNX bus access, red wire connected to “+”, black wire connected to “-“;
4. वर्णन: Reset button, short press to enter the reset operation, used for KNX bus power supply re-output;
5. वर्णन: Reset indicator, the indicator light is red, then the bus reset operation is performed;
6. वर्णन: Status is the power supply working status indicator, green status LED, when the status LED is always on, it means that the power supply is working normally;
7. वर्णन: Overload is the overload protection indicator, when the bus output current is overcurrent or the bus is short-circuited, the LED indicator flashes red;
   

Power Supply Operation Test

After the bus power supply is correctly installed, turn on the main power supply and supply power to the bus power supply. At this time, the Status indicator on the device is on and the other lights are off, indicating that the bus power supply can operate normally.

Safe Use And Maintenance

1. वापरण्यापूर्वी सर्व सूचना काळजीपूर्वक वाचा.
2. Create a well-ventilated environment.
3. During use, pay attention to moisture, shock and dust prevention.
4. Do not expose to rain, other liquids or corrosive gases.
5. If the machine is damp or invaded by liquid, it should be dried in time.
6. If the machine fails, please contact professional maintenance personnel or our company.

कागदपत्रे / संसाधने

Light Control LC-PS1280/2 EIB/KNX BUS Data Transfer [pdf] वापरकर्ता मॅन्युअल LC-PSB1280-2, LC-PS1280-2, LC-PS12802 EIB KNX BUS Data Transfer, LC-PS12802, EIB KNX BUS Data Transfer, BUS Data Transfer, Data Transfer

संदर्भ

• वापरकर्ता मॅन्युअल