स्विफ्ट®
LINK TEST QUICK START GUIDE

REQUIRED TOOLS AND EQUIPMENT TO PERF ORM LINK TEST

लहान फ्लॅटहेड पेचकस	बॅटरीज CR123A 3v (Panasonic or Duracell) One per each device
2 किंवा अधिक SWIFT डिव्हाइसेस सर्व SWIFT उपकरणे फॅक्टरी डीफॉल्टमध्ये असणे आवश्यक आहे.	SWIFT Device Bases

OPTIONAL TOOLS TO ANALYZE LINK TEST DATA

Windows Laptop with SWIFT Tools Version 2.01	May need to be updated before use with SWIFT Tools. SWIFT Tools will automatically update the W-USB.

BEFORE PERFORMING A LINK TEST

उपकरणे आत असल्याची खात्री करा फॅक्टरी डीफॉल्ट
With the code wheels set to 000, insert one battery into the device. The LED on the front will blink red if the device is in factory default.
जर डिव्हाइस फॅक्टरी डीफॉल्टमध्ये नसेल, तर पुढील पृष्ठावरील प्रक्रिया अनुसरण करा.

फॅक्टरी डीफॉल्टवर डिव्हाइसेस रीसेट करा

SWIFT टूल्स वापरणे:

1. Insert the W-USB dongle into your computer and launch the SWIFT Tools application.
2. On the home screen you can select Site Survey, Create Mesh Network, or Diagnostics.
3. ऑपरेशन्स वर क्लिक करा आणि डिव्हाइसला फॅक्टरी डीफॉल्टवर सेट करा निवडा.
4. You are now on the Reset Devices screen. Select the desired device, and click Reset.

व्यक्तिचलितपणे:

1. Start with the device powered off.
2. Insert one single battery into any slot in the device. The LED will blink yellow once every 5 seconds for a minute.
3. Turn the SLC address wheels using a common screwdriver to 0, then to 159, then back to 0.
4. The device will blink green five times, followed by a single or double red blink. This is your confirmation the device is now on factory default.

वायरलेस डिव्हाइसची तयारी

1. Tamper each devices by removing the base or cover plate and remove batteries.
2. Use a screwdriver to address each device. Addresses must be between 001-100, and must be in ascending order. For example, if the first device is addressed 001, the second device should be 002. When the link test begins, each device will test the link between itself and the next lowest address.

लिंक चाचणी आयोजित करा

1. Insert one battery to power up the device with the lowest address.
   टीप: You can insert the battery into any slot on the device. Also once the battery is inserted the device LEDs will blink twice every 5 seconds. If the devices is not showing this pattern, it must be set to factory default, see previous page.
2. Take the device to the exact location where you plan to install it, in order to increase accuracy of the link test.
3. डिव्हाइसला त्याच्या बेसमध्ये फिरवा.
4. Observe LED pattern.
   It will blink yellow once every half second for about 20 seconds. Then turn solid red. The device is now ready to perform a link test to the device with the next highest SLC address. This device will be setup in step 5.
5. Insert one battery to power up the device with the next highest address.
   उदाample: 002 if the first device that was placed was 001.
6. Take the device to the exact location where you plan to install it in order to increase accuracy of the link test.
7. डिव्हाइसला त्याच्या बेसमध्ये फिरवा.
8. लिंक चाचणीच्या प्रगतीचे निरीक्षण करा.
   डिव्हाइसवरील LEDs 20 सेकंदांसाठी प्रत्येक अर्ध्या सेकंदाने एकदा ब्लिंक होतील. यानंतर, लिंक चाचणीचे निकाल पाहिले जाऊ शकतात.
9. लिंक चाचणी परिणामांचे निरीक्षण करा.
   4 ब्लिंक = उत्कृष्ट दुवा
   3 blinks = चांगला दुवा
   2 blinks = Marginal link
   1 blinks = Poor link
   लाल रंगात विकले = लिंक नाही
10. To test additional links, repeat steps 6-9 while the first and second devices are still mounted in their locations.

ANALYZE LINK TEST DATA IN SWIFT TOOLS (OPTIONAL)

1. Insert the W-USB into your laptop’s USB slot. Open SWIFT Tools.
   टीप: The W-USB may need to be updated before use with SWIFT Tools. SWIFT Tools will automatically update the W-USB..
2. Click Create in Create New Jobsite
   टीप: विद्यमान जॉब साइट देखील वापरली जाऊ शकते.
3. Enter jobsite information
   १. जॉबसाईटचे नाव एंटर करा आणि स्थान / वर्णन एंटर करा
   2. तयार करा क्लिक करा
4. Click the Start button under Site Survey.
5. Return devices that have completed the Link Test to factory default by placing them in tampएर
   Caution: Do not place the base or cover plate onto a device that is in the Pending Site Survey state or the existing results will be replaced. Reference the SWIFT manual for more information.
6. In the Communicator Panel, select the devices you want to retrieve data from.टीप: केवळ साइट सर्वेक्षण डेटा असलेली उपकरणे निवडली जाऊ शकतात.
   Devices collect site survey data by performing an RF Scan or Link Quality Test as discussed on pages 5 & 6.
7. Click the Retrieve button.
8. Once the data is retrieved, click the Next button near the bottom right of the screen to view the results of your link test.
9. View your Link Test results.
   ला view अधिक तपशीलवार निकालांसाठी, तपशीलवार वर क्लिक करा View.
   To export date to an Excel spreadsheet, click Export to Excel
   टीप: Link Test data will only appear on SWIFT if a full Link Test was completed on the selected devices.

अतिरिक्त समर्थनासाठी
notifier.com
ग्राहक सेवा:
५७४-५३७-८९००
टेक सपोर्ट
NOTIFIER.Tech@honeywell.com
५७४-५३७-८९००

कागदपत्रे / संसाधने

Honeywell SWIFT Wireless Gateway [pdf] वापरकर्ता मार्गदर्शक SWIFT, SWIFT Wireless Gateway, Wireless Gateway, Gateway

संदर्भ

• वापरकर्ता मॅन्युअल