ED-PAC3020 EDATEC इंडस्ट्रियल ऑटोमेशन आणि कंट्रोल्स वापरकर्ता मॅन्युअल

The ED-PAC3020 is a real-time CODESYS programmable automation
controller suitable for industrial control and IoT fields. It comes
pre-installed with a multi-core CODESYS runtime and offers
different memory configurations based on user requirements.

2. Hardware:

The device features commonly used interfaces such as HDMI, USB,
Ethernet, RS232, and RS485. It integrates an RTC and supports
connection to remote EtherCAT-based I/O modules.

3. Introduction to CODESYS Software:

The product supports CODESYS V3.5 SP19 and later versions for
programming and control.

4. Networking Application:

The device offers EtherCAT, Ethernet, RS485, and RS232
interfaces for multi-layer network communication to meet diverse
अर्ज आवश्यकता.

5. देखावा:

फ्रंट पॅनल:

RS232 port: Used to connect third-party control equipment.

Green UART indicators: Check the communication status of UART
बंदर
Red power indicator: Indicates device power status.

Green system status indicator: Shows system read/write
operations status.
Audio Output (HPO): Stereo audio output.

Audio Input (LINE IN): Supports stereo audio input.
RS485 port: Used to connect third-party control equipment.

USB 2.0 ports: Supports up to 480Mbps transmission rate.

वारंवार विचारले जाणारे प्रश्न (FAQ):

Q: Can I reinstall the operating system on the ED-PAC3020?

A: Reinstalling the operating system will invalidate the CODESYS
license that comes pre-installed by default. It is advised not to
attempt installing the OS on your own.

Q: What programming standards are supported by the
ED-PAC3020?

A: The device supports IEC 61131-3 programming standards and
industrial communication protocols like EtherCAT and Modbus
TCP.

View Fullscreen

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
वापरकर्ता मॅन्युअल
ईडीए टेक्नॉलॉजी कंपनी लिमिटेड द्वारे बांधलेले: २०२५-०८-०१

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
१ हार्डवेअर मॅन्युअल
हा धडा उत्पादनाची ओळख करून देतोview, CODESYS software, networking application, packaging list, appearance, buttons, indicators and interfaces.
1.1 ओव्हरview
The ED-PAC3020 is a real-time CODESYS programmable automation controller, pre-installed by default with a multi-core CODESYS runtime. Depending on the application scenario and user requirements, it offers programmable logic system configurations with either 2GB DDR + 128GB SSD or 8GB DDR + 256GB SSD .
WARNING The ED-PAC3020 device comes pre-installed with a valid CODESYS license by default. Reinstalling the operating system will invalidate the CODESYS license. Do not attempt to install the OS on your own.
The ED-PAC3020 provides commonly used interfaces such as HDMI, USB, Ethernet, RS232, and RS485, integrates RTC, and is primarily used in industrial control and IoT fields.
The ED-PAC3020 supports connection to remote EtherCAT-based I/O modules (e.g., couplers, DI, DO, AI, AO) via an EtherCAT network. The device integrates the CODESYS Control Runtime System, supporting IEC 61131-3 programming standards and industrial communication protocols like EtherCAT and Modbus TCP. Users can optionally enable additional functionalities by licensing features such as:
· TargetVisu · WebVisu · Softmotion · CNC + Robotics · EtherCAT Master · Modbus TCP Master · OPC UA Server
Custom configurations are available to meet specific application requirements.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
1.2 Introduction to CODESYS Software
CODESYS (Controller Development System) is an open industrial automation software development platform that provides a full-stack solution for programming, debugging, and maintaining programmable logic controllers (PLCs), industrial PCs (IPCs), and embedded control systems. Compliant with the IEC 61131-3 international standard, it supports complex logic control, multi-axis motion control, industrial communication protocol integration, and real-time data processing. It is widely used in smart manufacturing, energy management, logistics automation, and other industrial fields.
Key Features of CODESYS:
· Standardized Programming Language Support Full compatibility with the IEC 61131-3 programming languages: Ladder Diagram (LD) Function Block Diagram (FBD) Structured Text (ST) Instruction List (IL) Sequential Function Chart (SFC) Supports Object-Oriented Programming (OOP) extensions for large-scale complex projects.
· Cross-Platform Development & Deployment Development Environment: Compatible with Windows and Linux operating systems, offering a unified engineering interface. Target Systems: Deployable on 2,000+ industrial controller hardware platforms, including ARM/X86 architectures.
· Modular Engineering Libraries Prebuilt Libraries: Include industrial protocol stacks (Modbus/TCP, OPC UA, EtherCAT) and advanced control modules (PID control, CNC interpolation algorithms). Custom Libraries: Support encapsulation and reuse of Function Blocks and POUs (Program Organization Units).
· Visual Debugging & Diagnostic Tools Real-time monitoring of variables, I/O mapping, and task execution status with waveform analysis. Advanced debugging tools: breakpoints, step-by-step execution, and cross-referencing for rapid fault diagnosis. Integrated HMI development tools for seamless SCADA system integration.
The ED-PAC3020 supports CODESYS V3.5 SP19 and later versions.
1.3 नेटवर्किंग ऍप्लिकेशन
The ED-PAC3020 features EtherCAT, Ethernet, RS485 and RS232 interfaces, enabling multi-layer network communication to meet diverse application requirements across various scenarios. A typical application topology is illustrated in the figure below:

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

1.4 पॅकिंग सूची
· 1 x ED-PAC3020 Unit · 4 x Pads
1.5 देखावा
Introducing the functions and definitions of the interfaces on each panel
1.5.1 फ्रंट पॅनेल
Introducing front panel interface types and definitions.

नाही.

कार्य व्याख्या

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

नाही.

कार्य व्याख्या

1 x RS232 port, 3-Pin 3.5mm pitch phoenix terminal, which is used to connect the third-party control equipment.

४ x हिरवे UART इंडिकेटर, जे UART पोर्टची संप्रेषण स्थिती तपासण्यासाठी वापरले जाते.

१ x लाल पॉवर इंडिकेटर, जो डिव्हाइस पॉवर-ऑन आणि पॉवर-ऑफची स्थिती तपासण्यासाठी वापरला जातो.

1 x green system status indicator, which is used to view the status of system read/write operations.

1 x Audio Output (HPO), 3.5mm audio jack connector (green), stereo audio output.

1 x Audio Input (LINE IN), 3.5mm audio jack connector (red), supporting stereo audio input.

1 x RS485 port, 3-Pin 3.5mm pitch phoenix terminal, which is used to connect the third-party control 7
उपकरणे

2 x USB 2.0 ports, Type-A connector, each channel supports up to 480Mbps transmission rate.

2 x USB 3.0 ports, Type-A connector, each channel supports up to 5Gbps transmission rate.

1 x Ethernet interface (10/100/1000M auto-negotiation), RJ45 connector, EtherCAT communication 10
interface for connecting to EtherCAT networks, with PoE (Power over Ethernet) support.

1.5.2 मागील पॅनेल
Introducing rear panel interface types and definitions.

नाही.

कार्य व्याख्या

1 x power button, which is used to turn on and turn off the device.

1 x Micro SD card slot, reserved for future use.

Note: The device boots from the SSD by default. This Micro SD card slot is reserved for potential

विस्तार

1.5.3 साइड पॅनेल
Introducing side panel interface types and definitions.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

नाही.

कार्य व्याख्या

1 x DC input, USB Type-C connector, which supports 5V 5A power input.

2 x HDMI ports, Micro HDMI connector, which can connect a display and supports 4K 60Hz

1.6 बटण
The ED-PAC3020 includes a ON/OFF button, and the silkscreen is “ON/OFF”. If you run Raspberry Pi Desktop, you can initiate a clean shutdown by briefly pressing the power button. A menu will appear asking whether you want to shutdown, reboot, or logout:

टीआयपी
If you run Raspberry Pi Desktop, you can press the power button twice in quick succession to shut down.

1.7 सूचक

This section explains the status and meanings of the indicators integrated into the ED-PAC3020 device.

इंडिकेटर PWR ACT

Status On Blink Off Blink

Description The device has been powered on. Power supply of the device is abnormal, please stop the power supply immediately. The device is not powered on. The system started successfully and is reading and writing data.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

Indicator COM1~COM2 Yellow indicator of Ethernet port Green indicator of Ethernet port

Status Off On/Blink Off On Blink Off On Blink Off

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
Description The device is not powered on or does not read and write data. Data is being transmitted The device is not powered on or there is no data transmission. The Ethernet connection is in the normal state. The Ethernet connection is abnormal. The Ethernet connection is not set up. The Ethernet connection is in the normal state. Data is being transmitted over the Ethernet port. The Ethernet connection is not set up.

टीआयपी
The function of the PWR/ACT indicator on the Raspberry Pi 5 has been transferred to the separate PWR and ACT indicators by default, so the PWR/ACT indicator remains on after the device is powered on.

1.8 इंटरफेस
उत्पादनातील प्रत्येक इंटरफेसची व्याख्या आणि कार्य सादर करत आहे.
1.8.1 पॉवर इंटरफेस
The ED-PAC3020 device includes one power input interface, which utilizes a USB Type-C connector labeled “PWR IN” and supports a 5V 5A power input.
TIP In order for Raspberry Pi 5 to achieve better performance, it is recommended to use a 5V 5A power adapter.

1.8.2 1000M Ethernet Interface (EtherCAT)
The ED-PAC3020 device includes one auto-negotiating 10/100/1000M Ethernet interface with an
RJ45 connector featuring status LEDs, labeled as ” “. This interface serves as an EtherCAT communication port for connecting to EtherCAT networks and supports PoE (Power over Ethernet) power delivery.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
1.8.3 HDMI इंटरफेस
The ED-PAC3020 device includes 2 HDMI interfaces using Micro HDMI connectors, labeled “HDMI”, for connecting HDMI displays. These interfaces support video output up to 4Kp60.
TIP Some third-party Micro HDMI cables may have shorter Micro HDMI connectors, which could cause connection issues. It is recommended to use the official Raspberry Pi Micro HDMI to Standard HDMI cable for optimal compatibility.

1.8.4 USB 2.0 इंटरफेस
The ED-PAC3020 device includes 2 USB 2.0 interfaces with standard Type-A connectors, labeled as ” “. These interfaces support connecting standard USB 2.0 peripherals and offer a maximum transfer rate of 480Mbps.

1.8.5 USB 3.0 इंटरफेस
The ED-PAC3020 device includes 2 USB 3.0 interfaces with standard Type-A connectors, labeled as ” “. These interfaces support connecting standard USB 3.0 peripherals and offer a maximum transfer rate of 5Gbps.

1.8.6 RS232 इंटरफेस
The ED-PAC3020 device includes 1 RS232 interface with a 3-Pin 3.5mm pitch Phoenix terminal, labeled “TX/RX/GND”. Pin Definition Terminal pins are defined as follows:

पिन आयडी १ २ ३

Pin Name TX RX GND

The RS232 interface corresponds to the following pin names on the Pi5:

Signal TX RX

Pi5 GPIO Name GPIO4 GPIO5

Pi5 Pin Out UART3_TXD UART3_RXD

कनेक्टिंग केबल्स

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

RS232 वायरिंगची योजना खालीलप्रमाणे आहे:

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

1.8.7 RS485 इंटरफेस
The ED-PAC3020 device includes 1 RS485 interface with a 3-Pin 3.5mm pitch Phoenix terminal, labeled “A/B/GND”. Pin Definition Terminal pins are defined as follows:

पिन आयडी १ २ ३

Pin Name A B GND

The RS485 interface corresponds to the following pin names on the Pi5:

Signal A B

Pi5 GPIO Name GPIO12 GPIO13

Pi5 Pin Out UART5_TXD UART5_RXD

कनेक्टिंग केबल्स RS485 वायरिंग स्कीमॅटिक खालीलप्रमाणे आहे:

RS485 Terminating Resistor Configuration
The ED-PAC3020 device includes 1 RS485 interface. A 120 termination resistor is reserved between the A and B lines of the RS485 circuit. Inserting a jumper cap enables this termination resistor. By default, no jumper is installed, rendering the 120 termination resistor inactive. The termination resistor is located at J7 on the PCBA (printed circuit board assembly).
TIP The device case must be opened to inspect the 120 termination resistor.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
1.8.8 ऑडिओ इनपुट
The ED-PAC3020 device includes 1 audio input interface (LINE IN), a red 3.5mm audio jack, labeled as ” “, which supports stereo input.
1.8.9 ऑडिओ आउटपुट
The ED-PAC3020 device includes 1 audio output interface (HPO), a green 3.5mm audio jack, labeled as ” “, which supports stereo output.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
2 डिव्हाइस स्थापित करणे
The ED-PAC3020 device is designed for desktop placement by default and supports wall mounting with the optional ED-ACCBKT-L3020 wall-mount bracket from our company.
TIP The ED-PAC3020 packaging box does not include the ED-ACCBKT-L3020 by default. Users must purchase it separately.
Preparation: · Prepared a Phillips-head screwdriver. · Obtained the ED-ACCBKT-L3020 wall-mount bracket.
Step: 1. Use a Phillips screwdriver to unscrew the four M2.5 screws on the side of the ED-IPC3020
घड्याळाच्या उलट दिशेने.
2. Align the left and right brackets of the ED-ACCBKT-L3020 with the screw holes on both sides of the ED-PAC3020, insert the four M2.5*6 screws, and tighten them clockwise with a Phillips screwdriver to secure the ED-ACCBKT-L3020 to the sides of the ED-PAC3020.

3. Based on the spacing and diameter of the wall-mounting screw holes of the ED-ACCBKTL3020 left and right brackets (refer to the diagram below), drill holes in the wall accordingly, then proceed with wall-mounted installation of the device.
· Unit: mm · Tolerance: 0.5-6±0.05, 6-30±0.1, 30-120±0.15

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
3 उपकरण बूट करणे
This chapter details the specific procedures for connecting cables and powering on the device.
3.1 कनेक्टिंग केबल्स
This section describes the procedures for connecting cables to the device. Preparation:
· Obtained fully functional accessories such as a switch, monitor, mouse, keyboard, I/O expansion module, and power adapter.
· Available functional network connection. · Available functional cables: HDMI cable and Ethernet cable. Schematic diagram of connecting cables: Please refer to 1.8 Interface for the pin definition of each interface and the specific method of wiring.
TIP Some third-party Micro HDMI cables may have shorter Micro HDMI connectors, which could cause connection issues. It is recommended to use the official Raspberry Pi Micro HDMI to Standard HDMI cable for optimal compatibility.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

3.2 प्रथमच प्रणाली बूट करणे
Once the ED-PAC3020 is connected to power, the system will begin to boot up. · Red PWR indicator: Lights up to indicate the device is receiving power. · Green ACT indicator: Blinks to signal normal system startup. The Raspberry Pi logo will then appear in the upper-left corner of the screen.
TIP Default username is pi , default password is raspberry .
3.2.1 Raspberry Pi OS (डेस्कटॉप)
If the device is factory-installed with the Desktop OS, it will boot directly into the desktop interface upon startup, as shown in the figure below.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
3.2.2 रास्पबेरी Pi OS (लाइट)
If the device is factory-installed with the Lite OS, it will automatically log in using the default credentials after startup. The figure below indicates that the system has booted successfully.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
4 CODESYS Programming
This chapter details the specific operations involved in using CODESYS.
WARNING The ED-PAC3020 device comes pre-installed with a valid CODESYS license by default. Reinstalling the operating system will invalidate the CODESYS license. Do not attempt to install the OS on your own.
4.1 CODESYS Software Download and Installation
TIP The installed CODESYS IDE version must be 3.5.19 or higher, and the PC operating system must be Windows 10 or Windows 11 (64-bit recommended).
1. Download the installation package from the official CODESYS website. The download URL is https://store.codesys.com/de/ (https://store.codesys.com/de/) .
TIP When downloading from the CODESYS official website for the first time, you must first register and log in to your account.
2. Right-click the downloaded installer and select “Run as administrator” from the context menu. 3. Click “Install” in the opened installation interface, and keep the default configuration during the
स्थापना प्रक्रिया.

4. After the installation is complete, click “Finish” to close the installation interface.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

4.2 Obtaining and Installing Device Description File
Before connecting to the device via CODESYS, you need to download and install the device description file प्रथम
4.2.1 Obtaining Device Description File
TIP The device’s default Ethernet port IP address is 192.168.0.100. To modify it, refer to Configuring Ethernet IP.
तयारी:
· A CODESYS-authorized ED-PAC3020 is available. · A functional Ethernet cable is available. · A Windows PC is prepared, with its IP address configured to the same subnet as the device.
उदाample, if the device’s IP (1000M Ethernet port) is 192.168.0.100 , set the PC’s IP to 192.168.0.99 .
पायऱ्या:
1. Connect the device’s Ethernet port to the PC via an Ethernet cable, then power on the device. 2. Enter http://192.168.0.100:8100 in the PC’s web browser to access the “PLC Setting”
interface. 3. In the “Device Info” section, click the “[Download] Device Description File” button to download
the corresponding “.xml” format device description file.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

TIP Also available directly in the document ED-PAC3020 Device Fileo(phettnpsin://nveipw.1w23inpdaonw.cn/ 1826505135/17964309) .
4.2.2 Installing Device Description File
तयारी:
· A PC installed with CODESYS software version V3.5 SP19 (64-bit). · An ED-PAC3020 device with a valid CODESYS license and its corresponding device
वर्णन file. · Connect both the PC and ED-PAC3020 to the network, ensuring their IP addresses are within
समान सबनेट.
पायऱ्या:
1. Double-click the CODESYS icon on the PC desktop to open the CODESYS software. From the menu bar, select “Tools” “Device Repository”.

2. In the opened “Device Repository” pane, click “Install”.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

3. In the pop-up “Install Device Description” pane, select the device description file to be installed and click “Open” to proceed with the installation.
4. After successful installation, you can verify in the “Device Repository” that the device description file have been added successfully.

4.2.3 Installing Remote I/O Device Description File
तयारी:
· A PC installed with CODESYS software version V3.5 SP19 (64-bit). · An ED-PAC3020 device with a valid CODESYS license. · The remote I/O device description files have been downloaded from: Remote I/O Description
Fileso(phettnpsin://nveipw.1w23inpdaonw.cn/1826505135/16632390) .

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
· Connect the PC, ED-PAC3020, and remote I/O devices to the same switch. Ensure that the IP addresses of the PC, ED-PAC3020, and remote I/O devices are within the same subnet.
Steps: 1. Double-click the CODESYS icon on the PC desktop to open the CODESYS software. From the
menu bar, select “Tools” “Device Repository”.
2. In the opened “Device Repository” pane, click “Install”.

3. In the pop-up “Install Device Description” pane, select the I/O device decirption file to be installed and click “Open” to proceed with the installation.
4. After successful installation, you can verify in the “Device Repository” that the I/O device description file have been added successfully.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
4.3 हार्डवेअर कॉन्फिगरेशन
तयारी:
· A PC installed with CODESYS software version V3.5 SP19 (64-bit). · The device description files and remote I/O device description files have been installed. · Connect the PC, ED-PAC3020, and remote I/O devices to the same switch. Ensure that the IP
addresses of the PC, ED-PAC3020, and remote I/O devices are within the same subnet.
4.3.1 Create a New Project and Connect to the Device
पायऱ्या:
1. Power on the ED-PAC3020 and the remote I/O modules. Open the CODESYS software on the PC, select “File” “New Project” in the menu bar to open the “New Project” pane, and create a standard project.

2. Select the installed device description file आणि "ओके" वर क्लिक करा.

3. Double-click the device, select “Scan Network” on the right, then choose the detected device from the scan results, and click “OK” to confirm.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

TIP · If the device cannot be detected during scanning, manually enter the IP address in the target device settings to connect. · If a device login prompt appears, log in with your credentials (username and password) or follow the instructions to register a new account.
4. As shown in the figure below, this indicates the device is successfully connected.

4.3.2 Adding Remote I/O Modules
Steps: 1. Right-click “Device” and select “Add Device” in the menu to add the EtherCAT Master.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

2. Double-click on the EtherCAT Master device to set the source address (Select the EtherCAT port, which corresponds to the device’s eth0 port).

3. Click the button to log in to the device. A successful login is shown in the figure below.

4. Click on the EtherCAT Master device, select “Scan for Devices” in the right-click menu, and copy all devices to the project after scanning is completed.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

5. Click the button to log out of the device. 6. Double-click the slave device, configure the relevant parameters in the right-hand interface,
enable “Expert settings”, select “Enable” under Select DC section, and select “Enable Sync0”.

7. Click the button to download the program to the device, then click the button to run it. As shown in the figure below, this indicates a successful operation.

4.4 प्रोग्रामिंग
खालील माजीample demonstrates practical programming using a specific coding scenario.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

4.4.1 Programming Process

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

4.4.2 Programming Example
Complete the development and debugging of a program for a timed blinking LED using a PNPtype 8-channel digital output (DO) module.
तयारी:
· A standard project has been created. · Hardware configuration has been completed. · A 24V compact LED lamp has been connected to the first output port of the remote DO (Digital
Output) module.
पायऱ्या:
1. Double-click the DO module, select “Module I/O Mapping” “Output” in the right-hand interface, and view the addresses of all output ports. As illustrated below, the first output port’s address is %QX18.0 .

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

2. Click “PLC_PLG” to open the programming interface, where the upper section is the variable declaration area and the lower section is the main program editing area.

3. Write the program code as follows:
PROGRAM PLC_PRG VAR
TON_TIME : TON; Light_Output : BOOL := FALSE;
END_VAR
TON_TIME(IN := NOT TON_TIME.Q, PT := T#0.5S);
IF TON_TIME.Q THEN Light_Output := NOT Light_Output;
ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

TON_TIME(IN := FALSE); END_IF
%QX18.0:= Light_Output;

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

4. After completing the program, click ” ” to compile it and ensure there are no errors.

5. Click Login to download the program to the device, then click Run to observe the LED blinking every 0.5 seconds.

4.5 ऑपरेशन आणि देखभाल

After downloading the program to the device, you can perform the Run and Stop operations.

Status Run Program Stop Program

Operations In the main menu of the software interface, click the Login button. In the main menu of the software interface, click the stop button.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
5 प्रणाली कॉन्फिगर करणे
या प्रकरणात सिस्टम कशी कॉन्फिगर करायची ते सादर केले आहे.
WARNING The ED-PAC3020 device comes pre-installed with a valid CODESYS license by default. Reinstalling the operating system will invalidate the CODESYS license. Do not attempt to install the OS on your own.
5.1 डिव्हाइस IP शोधणे
डिव्हाइस आयपी शोधत आहे
5.2 रिमोट लॉगिन
रिमोट लॉगिन
5.3 Wi-Fi कॉन्फिगर करत आहे
वाय-फाय कॉन्फिगर करत आहे
5.4 इथरनेट आयपी कॉन्फिगर करणे
इथरनेट आयपी कॉन्फिगर करणे
5.5 Configuring Bluetooth
ब्लूटूथ कॉन्फिगर करत आहे
5.6 बझर कॉन्फिगर करणे
The buzzer is controlled using GPIO6. Execute the following command to turn on the buzzer:
sh pinctrl set 6 op dh
Execute the following command to turn off the buzzer:

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

pinctrl set 6 op dl

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
sh

5.7 RTC कॉन्फिगर करणे
आरटीसी कॉन्फिगर करणे
५.१० सिरीयल पोर्ट कॉन्फिगर करणे
या प्रकरणात RS232 आणि RS485 च्या कॉन्फिगरेशन पद्धतीचा परिचय करून दिला आहे.
5.8.1 Installing Picocom Tool
लिनक्स वातावरणात, तुम्ही RS232 आणि RS485 सिरीयल पोर्ट डीबग करण्यासाठी picocom टूल वापरू शकता. picocom टूल स्थापित करण्यासाठी खालील कमांड कार्यान्वित करा.
sh sudo apt-get picocom स्थापित करा

५.१०.२ RS5.8.2 कॉन्फिगर करणे
The ED-PAC3020 contains 1 RS232 interface, and its corresponding COM port and device files are listed in the table below:

RS232 पोर्टची संख्या 1

संबंधित COM पोर्ट COM1

संबंधित डिव्हाइस File /dev/com1

Preparation: The RS232 ports of ED-PAC3020 has been connected with external device. Steps: 1. Execute the following command to open the serial port com1, and configure the serial port baud
११५२०० पर्यंत दर.

श पिकोकॉम -बी ११५२०० /डेव्ह/कॉम१

२. बाह्य उपकरण नियंत्रित करण्यासाठी आवश्यकतेनुसार इनपुट कमांड.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

५.१०.२ RS5.8.3 कॉन्फिगर करणे
The ED-PAC3020 contains 1 RS485 interface, and its corresponding COM port and device files are listed in the table below:

RS485 पोर्टची संख्या 1

संबंधित COM पोर्ट COM2

संबंधित डिव्हाइस File /dev/com2

Preparation: The RS485 ports of ED-PAC3020 has been connected with external device. Steps: 1. Execute the following command to open the serial port com2, and configure the serial port baud
११५२०० पर्यंत दर.

श पिकोकॉम -बी ११५२०० /डेव्ह/कॉम१

२. बाह्य उपकरण नियंत्रित करण्यासाठी आवश्यकतेनुसार इनपुट कमांड.

5.9 ऑडिओ कॉन्फिगर करणे

ऑडिओ कॉन्फिगर करत आहे

5.10 CODESYS License Management

The ED-PAC3020 device comes pre-installed with a CODESYS license by default. You can back up and restore the license by accessing the “PLC Setting” interface.

5.10.1 License Backup

तयारी:

· A Windows PC has been set up with an IP address in the same subnet as the device. For example, if the device’s IP (1000M Ethernet port) is 192.168.0.100 , set the PC’s IP to 192.168.0.99 .
· A functioning Ethernet cable has been prepared.

पायऱ्या:

1. Connect the device’s 1000M Ethernet port to the PC via an Ethernet cable, then power on the device.
2. Enter http://192.168.0.100:8100 in the PC’s web browser to access the “PLC Setting” interface.
3. In the “Codesys License Management” interface, click “Backup License” to download the license file and save it locally.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

TIP The backed-up license file can only be restored on the same device.
5.10.2 License Restore
तयारी:
· A Windows PC has been set up with an IP address in the same subnet as the device. For example, if the device’s IP (1000M Ethernet port) is 192.168.0.100 , set the PC’s IP to 192.168.0.99 .
· A functioning Ethernet cable has been prepared. · The backed-up license file प्राप्त झाले आहे.
पायऱ्या:
1. Connect the device’s 1000M Ethernet port to the PC via an Ethernet cable, then power on the device.
2. Enter http://192.168.0.100:8100 in the PC’s web browser to access the “PLC Setting” interface.
3. In the “Codesys License Management” interface, click “Restore License”.

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

ED-PAC3020 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.

4. As prompted, select the obtained license file under a custom path. 5. After a successful License Restore, a 100% progress bar will be displayed in the right-hand
पटल

6. Open the device’s terminal command pane, execute the following command, and restart the device.
sh sudo रीबूट करा

ईमेल: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn

फोन: +८६-१५९२१४८३०२८ (चीन) | +८६-१८२१७३५१२६२ (परदेशी)

कागदपत्रे / संसाधने

EDA ED-PAC3020 EDATEC Industrial Automation and Controls [pdf] वापरकर्ता मॅन्युअल
ED-PAC3020 EDATEC Industrial Automation and Controls, ED-PAC3020, EDATEC Industrial Automation and Controls, Industrial Automation and Controls, Automation and Controls

संदर्भ

वापरकर्ता मॅन्युअल

ED-PAC3020 EDATEC इंडस्ट्रियल ऑटोमेशन आणि कंट्रोल्स वापरकर्ता मॅन्युअल

ED-PAC3020 EDATEC औद्योगिक ऑटोमेशन आणि नियंत्रणे

तपशील:

उत्पादन वापर सूचना:

1. ओवरview:

2. Hardware:

3. Introduction to CODESYS Software:

4. Networking Application:

5. देखावा:

फ्रंट पॅनल:

वारंवार विचारले जाणारे प्रश्न (FAQ):

Q: Can I reinstall the operating system on the ED-PAC3020?

Q: What programming standards are supported by the
ED-PAC3020?

कागदपत्रे / संसाधने

संदर्भ

एक टिप्पणी द्या

उत्तर रद्द करा