इकोनॉक्स एम४० पर्यायी घटक डीamper स्थापना
तपशील
- उत्पादन: M40 Optional Component
- निर्माता: Econox
- स्थान: Parkforum 1047, 5657 HJ Eindhoven, The Netherlands
- Webसाइट: www.econox.nl
- ईमेल: info@econox.nl
उत्पादन वापर सूचना
Post Heater Installation
- इलेक्ट्रिकल बॉक्स उघडा.
- Make the external 3P+N+PE connection.
- Connect the signal cables to the device panel using plug & play sockets.
हवा तापमान सेन्सर पुरवठा
- Connect the external sensor.
- Disconnect the internal sensor cable.
Post Heater Installation
- Open the electrical box and make the external 3P+N+PE connection. Connect the signal cables to the device panel using plug & play sockets.
हवा तापमान सेन्सर पुरवठा
- After connecting the external sensor, the internal sensor cable must be disconnected.
Connection terminals in a wiring diagram
वॉटर हीटर कॉइल
After connecting the external sensor, the internal sensor cable must be disconnected.
हवा तापमान सेन्सर पुरवठा
तापमान सेन्सर कनेक्शन
Frost Protection Thermostat Connection
The frost thermostat is mounted on the water coil and is supplied with a cable. The cable must be connected to the relevant terminals on the panel as described below.
Damper स्थापना
- दिamper motor cables are supplied ready for use. The cables must be connected to the relevant terminals on the panel as described below.
- TB6:6 Open terminal,
- TB6:7 Close terminal,
- TB6:8 GND
- Both the fresh air and exhaust dampers are connected to the same point.
Cooling Coil & Dx Coil
- हवा तापमान सेन्सर पुरवठा
Change over coil
हवा तापमान सेन्सर पुरवठा
Frost Protection Thermostat Sensor
चेंजओव्हर सेन्सर
- The temperature of the pipe at the coil inlet must be detected by the PLC in order for the coil to operate in both heating and cooling modes.
- The changeover sensor for this process is shipped disassembled.
- The sensor should be mounted to the point shown in the picture on the istallation. !!
- The installation must be set up with a 3-way valve. A 2-way valve should not be used.
- For the installation process, place the sensor on the pipe and tightly fasten the chain as shown in the picture.
- Sensor cable must be connected to the C and 2 terminals as shown in the picture below.
Scenario Table
- The system operates based on combinations of installed options.
To define the correct control logic:
- Fill out the table below accordingly.
- Notify Maxivent by Econox of the selected scenario.
- Maxivent by Econox will send the scenario software.
- ECONOX/Client must be installed as per the selected scenario.
Example कोड: 40-07-CO2-None-PH-None-COC
ग्राहक सेवा
- Econox
- Parkforum 1047
- 5657 HJ Eindhoven
- नेदरलँड
- www.econox.nl
- info@econox.nl
वारंवार विचारले जाणारे प्रश्न
How do I define the correct control logic for the system?
To define the correct control logic. Fill out the scenario table accordingly. Notify Maxivent by Econox of the selected scenario. Maxivent by Econox will send the scenario software. ECONOX/Client must be installed as per the selected scenario.
कागदपत्रे / संसाधने
 |
इकोनॉक्स एम४० पर्यायी घटक डीamper स्थापना [pdf] स्थापना मार्गदर्शक M40, sk22286, M40 Optional Component Damper Installation, M40, Optional Component Damper Installation, Component Damper Installation, Damper Installation, Installation |