सिस्को पीआयएम सेल्युलर प्लगेबल इंटरफेस मॉड्यूल वापरकर्ता मॅन्युअल

सिस्को पीआयएम सेल्युलर प्लगेबल इंटरफेस मॉड्यूल

तपशील

• सिम लॉक आणि अनलॉक क्षमतांना समर्थन देते
• बॅकअपसाठी ड्युअल सिम सपोर्ट
• योग्य फर्मवेअरसाठी ऑटो सिम सक्रियकरण
• पब्लिक लँड मोबाईल नेटवर्क (PLMN) निवड
• खाजगी LTE आणि खाजगी 5G नेटवर्क समर्थन
• दोन सक्रिय पीडीएन प्रोfileसेल्युलर इंटरफेसवर
• IPv6 डेटा ट्रॅफिकसाठी समर्थन
• सिस्को आयओएस-एक्सई वर सेल्युलर सेवाक्षमता वैशिष्ट्ये

सेल्युलर पीआयएम कॉन्फिगर करण्यासाठी पूर्व-आवश्यकता

नोंद

You must have the appropriate antennas and antenna accessories to complete your installation. Consult the Cisco Industrial Routers and Industrial Wireless Access Points Antenna Guide for suggestions on possible solutions.

• If the signal is not good at the router, place the antenna away from router in a better coverage area. Please refer to the RSSI/SNR values as displayed through show cellular <x/x/x> all or the LED of the pluggable modem.
• You must have cellular network coverage where your router is physically placed. For a complete list of supported carriers.
• You must subscribe to a service plan with a wireless service provider and obtain a Subscriber Identity Module (SIM) card. Only micro SIMs are supported.
• You must install the SIM card before configuring the Cellular PIM or router.
• The standalone antenna that supports GPS capabilities must be installed for the GPS feature to work when available on the PIM.

सेल्युलर पीआयएम कॉन्फिगर करण्यासाठी निर्बंध

• Currently, cellular networks support only user initiated bearer establishment.
• Due to the shared nature of wireless communications, the experienced throughput varies depending on the radio network capabilities, number of active users or congestion in a given network.
• Cellular bandwidth is asymmetric with the downlink data rate being greater than the uplink data rate, while on private cellular with TDD frequency band(s), it may be symmetrical.
• Cellular networks have higher latency compared to wired networks. Radio latency rates depend on the technology and carrier. Latency also depends on the signal conditions and can be higher because ofnetwork congestion.
• CDMA-EVDO, CDMA-1xRTT, and GPRS technology modes are not supported. 2G is only supported on the P-LTE-GB.
• Any restrictions that are part of the terms of service from your carrier.
• SMS—Only one text message up to 160 characters to one recipient at a time is supported. Larger texts are automatically truncated to the proper size before being sent.

वैशिष्ट्ये समर्थित नाहीत

The following features are not supported:

• On Cisco IOS-XE, TTY support or Line is not available on cellular interface as it was on IOS classic.
• On Cisco IOS-XE, explicit Chat script /Dialer string doesn’t need to be configured for the cellular interface as it was on IOS classic.
• DM log output to USB flash is not supported
• व्हॉइस सेवा

सेल्युलर पीआयएमची प्रमुख वैशिष्ट्ये

The PIM supports the following major features:

वारंवार विचारले जाणारे प्रश्न

• प्रश्न: मी सिस्को सेल्युलर प्लगेबल इंटरफेस मॉड्यूलसह कोणत्याही प्रकारचे अँटेना वापरू शकतो का?
  • A: No, it is recommended to use antennas and accessories specified in the Cisco Industrial Routers and Industrial Wireless Access Points Antenna Guide for compatibility and performance.
• प्रश्न: किती पीडीएन प्रो?fileसेल्युलर इंटरफेसवर s सक्रिय असू शकतात का?
  • अ: दोन पीडीएन प्रो पर्यंतfiles can be active on the Cellular interface, depending on the SIM subscription and services.