AXBUC-VW92 बॅकअप कॅमेरा रिटेन्शन इंटरफेस
“
तपशील:
- Product Name: AXBUC-VW92 Backup Camera Retention Interface
- Compatibility: Select Volkswagen/Skoda Models 2008-2015 with
RNS510 (MFD3), RNS315, Columbus (Skoda), or RCD510 (with 26-pin
कनेक्टर)
उत्पादन वापर सूचना:
स्थापना चरण:
- Connect the Ground wire from the VW92 to the aftermarket
radio’s ground wire. - Connect the Yellow wire from the VW92 to the Yellow wire of
your aftermarket radio. - Connect the Purple wire to the reverse trigger from your
vehicle or interface. - कॅम आउट व्हिडिओ केबल मागील बाजूस प्लग इन करा. view कॅमेरा इनपुट
of your aftermarket radio. - इंटरफेस बॉक्समध्ये पांढरा कनेक्टर प्लग इन करा.
- Plug in the vehicle connector and perform a test.
डिप स्विच सेटिंग्ज:
Refer to the instructions included with the product for dip
सेटिंग्ज स्विच करा.
वारंवार विचारले जाणारे प्रश्न:
Q: What vehicles are compatible with the AXBUC-VW92 Backup
Camera Retention Interface?
A: The interface is compatible with various Volkswagen and Skoda
models ranging from 2008 to 2015. Refer to the user manual or visit
AxxessInterfaces.com for specific applications.
Q: Why should I disconnect the negative battery terminal before
प्रतिष्ठापन?
A: Disconnecting the battery terminal ensures safety during
installation, especially when dealing with sensitive electrical
connections like airbag indicators. Always follow safety
मॅन्युअल मध्ये प्रदान केलेली खबरदारी.
"`
AXBUC-VW92 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
इन्स्टॉलेशन सूचना
Backup Camera Retention Interface Fits Select Volkswagen/Skoda Models 2008-2015*
* For vehicles equipped with RNS510 (MFD3), RNS315, Columbus (Skoda), or RCD510 (with 26-pin connector)
TABLE OF CONTENTS Connections: BLK-AXBUC-VW92………………………2 Installing the Interface……………………………………3 Dip Switch Settings…………………………………………3
इंटरफेस वैशिष्ट्ये
· Retains the OEM camera to an aftermarket radio · Plug-and-play, no cutting of wires required · For vehicles equipped with RNS510 (MFD3), RNS315, Columbus
(Skoda), or RCD510 (with 26-pin connector)
आवश्यक साधने
· Crimping tool and connectors, or solder gun, solder, and heat shrink · Tape · Wire cutter
· Zip ties
INTERFACE COMPONENTS · AXBUC-VW92 interface
· BLK-AXBUC-VW92 harness
NOTE: If your vehicle has a motorized OE camera door or active guidelines, you will need an interface that can enable the camera door to open, the AXBUC-VW2 will not retain these function. The AXBUC-VW2 will only retain the camera.
अर्ज
Volkswagen Amarok ……………………………………..2010-2014 EOS ………………………………………….. 2009-2014 Golf …………………………………………..2008-2014 Jetta …………………………………………2009-2014
Passat ………………………………………..2010-2015 Polo ………………………………………….2008-2014 Scirocco …………………………………….2008-2015 Tiguan ………………………………………. 2009-2015 Touran ……………………………………….2010-2015
Transporter ……………………………….2009-2014
Skoda Octavia ……………………………………..2009-2012 Superb ……………………………………..2008-2015
उत्पादनाबद्दल अधिक तपशीलवार माहिती आणि अद्ययावत माहितीसाठी AxxessInterfaces.com ला भेट द्या.
vehicle specific applications
ATTENTION: With the key out of the
ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections, especially the air bag indicator lights, are plugged in before reconnecting the battery or cycling the ignition to test this product. NOTE: Refer also to the instructions included with the aftermarket radio.
AxxessInterfaces.com
P कॉपीराइट 2025 मेट्रा इलेक्ट्रॉनिक्स कॉर्पोरेशन
REV. 8/18/25 INSTAXBUC-VW92
Interface End View
ON VE 23 4
Dipswitch See Dipswitch Settings
पुढील पृष्ठावर
कनेक्शन: BLK-AXBUC-VW92
इंटरफेस
BLK-AXBUC-VW92
आफ्टरमार्केट रेडिओ
समोर
(तुमच्या रेडिओची वैशिष्ट्ये भिन्न असू शकतात)
मागील View
AUX-IN मागील
SWC उप
CAM OUT
वाहन कनेक्टर
Radio Connections Black – Ground wire Yellow – Battery wire Purple – Reverse
2
इंटरफेस आणि डिप स्विच सेटिंग्ज स्थापित करणे
· Connect the AXBUC-VW92 to the wiring harness in the vehicle located at the radio location (26-pin connector).
Installation Steps 1. Connect Ground wire from the VW92 to the aftermarket radio’s ground wire. 2. Connect the Yellow wire from the VW92 to the Yellow wire of your aftermarket radio. 3. Purple is a Reverse input, connect the reverse trigger from your vehicle or interface to
this wire. Do not connect this wire to the vehicle’s BCM for the reverse signal. VW uses PWM circuitry, if connected to the BCM, the backup camera will flicker while the vehicle is running. You must find a dedicated reverse signal or use an interface that provides a reverse output. 4. Plug in the CAM OUT Video cable into the rear view camera input of your aftermarket radio. 5. Plug in the White connector into the interface box. 6. Plug in the vehicle connector and test.
Dip Switch Settings If after the AXBUC-VW2 is installed your screen quickly flashes the backup camera, or is displaying a blank screen when you put the vehicle into reverse, you will need to adjust the dip switches on the side of the interface. If screen is blank or flashing while in reverse, try this sequence.
Interface End View
ON VE 23 4
ON VE Dipswitch Detail
०६ ४०
Step 1 – Set Dip Switch 3 to OFF. – If not working go to step 2. Step 2 – Move all Dip Switches to OFF – If not working go to step 3. Step 3 – Flip Dip Switch 3 ON, leaving 1,2,4 OFF.
REV. 8/18/25 INSTAXBUC-VW92 3
AxxessInterfaces.com
AXBUC-VW92 साठी चौकशी सबमिट करा, आम्ही तुमच्याशी २४ तासांत संपर्क करू.
इन्स्टॉलेशन सूचना
अडचणी येत आहेत? आम्ही मदतीसाठी येथे आहोत. आमच्या टेक सपोर्ट लाइनशी येथे संपर्क साधा:
५७४-५३७-८९००
किंवा ईमेल द्वारे: techsupport@metra-autosound.com
टेक सपोर्ट तास (पूर्व मानक वेळ) सोमवार - शुक्रवार: 9:00 AM - 7:00 PM शनिवार: 10:00 AM - 5:00 PM रविवार: 10:00 AM - 4:00 PM
P कॉपीराइट 2025 मेट्रा इलेक्ट्रॉनिक्स कॉर्पोरेशन
Metra MECP प्रमाणित तंत्रज्ञांची शिफारस करते
REV. 5/27/25 INSTAXBUC-VW92
कागदपत्रे / संसाधने
 |
AXXESS AXBUC-VW92 Backup Camera Retention Interface [pdf] सूचना पुस्तिका AXBUC-VW92 Backup Camera Retention Interface, AXBUC-VW92, Backup Camera Retention Interface, Camera Retention Interface, Retention Interface, Interface |