1. परिचय
This instruction manual provides essential information for the safe and effective installation, operation, and maintenance of your Hella Proj-Light SL60 LED Blue Worklight. Please read this manual thoroughly before attempting to install or operate the product. Retain this manual for future reference.
2. सुरक्षितता माहिती
उत्पादन आणि वाहनाला दुखापत किंवा नुकसान टाळण्यासाठी नेहमी खालील सुरक्षा खबरदारी पाळा.
- Disconnect the vehicle's battery before beginning any electrical work to prevent electrical shock or short circuits.
- ऑपरेटिंग व्हॉल्यूमची खात्री कराtage of the worklight (10-80V) is compatible with your vehicle's electrical system.
- Do not look directly into the light beam when the light is active, as it may cause eye damage.
- Mount the worklight securely to prevent it from dislodging during vehicle operation.
- Route cables away from hot surfaces, sharp edges, and moving parts to prevent damage.
- स्थापनेदरम्यान योग्य वैयक्तिक संरक्षक उपकरणे (पीपीई) वापरा.
3. पॅकेज सामग्री
स्थापनेला पुढे जाण्यापूर्वी सर्व घटक उपस्थित आहेत याची खात्री करा:
- 1 x Hella 996210001 Proj-Light SL60 LED Blue 10-80V Worklight
4. सेटअप आणि स्थापना
Follow these steps for proper installation of the Hella Proj-Light SL60 LED Worklight.
4.1 माउंटिंग
Select a suitable mounting location on your vehicle that provides clear visibility and is structurally sound. The worklight comes with an adjustable mounting bracket.
- Position the mounting bracket at the desired location and mark the drilling points.
- Drill pilot holes if necessary, ensuring not to damage any underlying components.
- Secure the bracket using appropriate fasteners (not included, unless specified in package contents).
- Attach the worklight to the bracket using the provided bolt and nut, allowing for angle adjustment.
Figure 1: Hella Proj-Light SL60 LED Worklight showing the mounting bracket and heat sink fins.
4.2 वायरिंग
The Hella Proj-Light SL60 is designed for 10-80V DC electrical systems. Ensure correct polarity during connection.
- Identify the positive (+) and negative (-) wires from the worklight.
- Connect the positive wire of the worklight to a switched 10-80V DC power source (e.g., a dedicated switch or existing auxiliary circuit) using appropriate gauge wiring and a fuse.
- Connect the negative wire of the worklight to a reliable ground point on the vehicle chassis.
- शॉर्ट सर्किट आणि गंज टाळण्यासाठी सर्व कनेक्शन सुरक्षित आणि इन्सुलेटेड असल्याची खात्री करा.
आकृती 2: मागील view of the Hella Proj-Light SL60 LED Worklight with power cable.
२.१ परिमाणे
Refer to the diagram below for the physical dimensions of the worklight (measurements in millimeters).
Figure 3: Dimensional drawing of the Hella Proj-Light SL60 LED Worklight.
5. ऑपरेशन
Once properly installed and wired, the Hella Proj-Light SL60 LED Worklight can be operated via the connected switch.
- Activate the switch to turn the worklight ON.
- Deactivate the switch to turn the worklight OFF.
- Adjust the angle of the worklight by loosening the mounting bolt, repositioning the light, and then securely tightening the bolt.
The blue light projection is designed to enhance safety by indicating the presence and direction of moving vehicles or equipment, such as forklifts in warehouses or industrial settings.
6. देखभाल आणि काळजी
The Hella Proj-Light SL60 LED Worklight is designed for durability and minimal maintenance. Regular inspection and cleaning will ensure optimal performance.
- स्वच्छता: Clean the lens and housing periodically with a soft cloth and mild soap solution. Avoid abrasive cleaners or solvents that could damage the lens or finish.
- तपासणी: Regularly check the mounting hardware for tightness and inspect the wiring for any signs of wear, fraying, or corrosion. Replace any damaged components immediately.
- एलईडी लाइफ: The LED elements have an estimated operating life of 50,000 hours and do not require replacement under normal operating conditions.
7. समस्या निवारण
If you encounter issues with your Hella Proj-Light SL60, refer to the following table for common problems and solutions.
| समस्या | संभाव्य कारण | उपाय |
|---|---|---|
| प्रकाश चालू होत नाही. | No power supply; Blown fuse; Incorrect wiring; Faulty switch. | Check power connections; Inspect and replace fuse if necessary; Verify wiring polarity and connections; Test or replace switch. |
| प्रकाश मंद आहे किंवा लुकलुकत आहे. | कमी व्हॉलtage; Loose connection; Corroded terminals. | वाहन व्हॉल्यूम तपासाtage; Tighten all electrical connections; Clean any corroded terminals. |
| माउंटिंग ब्रॅकेट सैल आहे. | Fasteners are not tight. | Tighten all mounting bolts and nuts securely. |
8. तांत्रिक तपशील
| वैशिष्ट्य | तपशील |
|---|---|
| ब्रँड | हेला |
| मॉडेल | 996210001 |
| खंडtage | 10-80 व्ही डीसी |
| हलका प्रकार | एलईडी वर्कलाइट |
| हलका रंग | निळा |
| ऑपरेटिंग लाइफ | 50,000 तास |
| परिमाण (उत्पादन) | 4 x 5 x 4 इंच (अंदाजे) |
| आयटम वजन | 12.7 औंस |
| उत्पादक भाग क्रमांक | 996210001 |
| UPC | 760687177890 |
७. वॉरंटी आणि ग्राहक समर्थन
Hella products are manufactured to high-quality standards and are backed by a manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty documentation provided with your purchase for specific terms and conditions.
For technical assistance, warranty claims, or further inquiries, please contact Hella customer support through their official website or authorized distributors. Keep your proof of purchase and product model number (996210001) readily available when contacting support.
