GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

परिचय

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

सुरक्षितता माहिती

चेतावणी: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• स्थापनेपूर्वी सर्किट ब्रेकरवर वीज बंद असल्याची खात्री करा.
• हे डिव्हाइस नॅशनल इलेक्ट्रिक कोड आणि स्थानिक नियमांनुसार स्थापनेसाठी आहे.
• Do not use in wet locations or where directly exposed to water.
• फक्त घरातील वापरासाठी.

पॅकेज सामग्री

• GoControl WS15Z5-1 Z-Wave Wall Switch
• स्थापना स्क्रू
• Wire Nuts (may vary by package)
• वापरकर्ता मॅन्युअल (हा दस्तऐवज)

सेटअप आणि स्थापना

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. वीज बंद करा: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. जुना स्विच काढा: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. तारा ओळखा:
   • ओळ (गरम): सहसा काळा, सर्किट ब्रेकरमधून येणारा.
   • लोड: Usually black, going to the light fixture or appliance.
   • तटस्थ: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • जमीन: सहसा हिरवा किंवा उघडा तांबे.
4. नवीन स्विच कनेक्ट करा: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • कनेक्ट करा ओळ wire to the terminal marked "LINE".
   • कनेक्ट करा लोड wire to the terminal marked "LOAD".
   • कनेक्ट करा तटस्थ wire to the terminal marked "NEUTRAL".
   • कनेक्ट करा ग्राउंड wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. माउंट स्विच: Carefully push the wired switch into the wall box. Secure it with the provided screws.
6. वॉल प्लेट स्थापित करा: Attach the new or existing wall plate.
7. पुनर्संचयित शक्ती: सर्किट ब्रेकरवर वीज पुन्हा चालू करा.

आकृती 1: समोर view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle एकदा. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

स्विच ऑपरेट करत आहे

मॅन्युअल नियंत्रण

• दाबा शीर्ष of the paddle to turn the connected load ON.
• दाबा तळाशी of the paddle to turn the connected load बंद.

Z-वेव्ह नियंत्रण

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

देखभाल

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• स्वच्छता: To clean the switch, wipe it with a soft, damp कापड अपघर्षक क्लीनर किंवा सॉल्व्हेंट्स वापरू नका.
• फर्मवेअर अद्यतने: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• सामान्य काळजी: स्विच जास्त आर्द्रता किंवा अति तापमानाच्या संपर्कात येत नाही याची खात्री करा.

समस्यानिवारण

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle एकदा. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

तपशील

हमी आणि समर्थन

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webसाइट किंवा त्यांच्या ग्राहक सेवा विभागाशी संपर्क साधा.

Webसाइट: www.gocontrol.com

निर्माता: GOCONTROL