IBO OHI 25-60/180 सर्कुलेशन पंप वापरकर्ता मॅन्युअल

1. उत्पादन संपलेview

The IBO OHI 25-60/180 circulation pump, also known as a heating pump, facilitates the movement of heating water within a heating system. This pump model features a manual 3-speed regulator, allowing for system adaptation. It is suitable for use in heating and air conditioning systems with fluid temperatures ranging from +2°C to +110°C.

मुख्य वैशिष्ट्यांचा समावेश आहे:

• Manual 3-speed regulator for optimal system adaptation.
• Suitable for heating and air conditioning systems with fluid temperatures from +2°C to +110°C.
• Constructed with a ceramic shaft, graphite radial bearing, stainless steel bearing plate and rear pot, and a grey cast iron pump housing.
• Compact design for easy installation.
• शांत ऑपरेशन.

Image 1: IBO OHI 25-60/180 Circulation Pump. This image displays the orange-colored pump unit with its black control panel, showing the speed selector and technical specifications. Two black rubber seals are visible at the bottom.

2. सुरक्षितता माहिती

स्थापना आणि ऑपरेशन करण्यापूर्वी सर्व सूचना काळजीपूर्वक वाचा. या सूचनांचे पालन न केल्यास विजेचा धक्का, आग किंवा गंभीर दुखापत होऊ शकते.

• विद्युत सुरक्षा: Ensure the power supply is disconnected before any installation, maintenance, or repair work. All electrical connections must be performed by a qualified electrician in accordance with local regulations. The pump requires a 230V, 50Hz power supply.
• पाण्याचे तापमान: The pump handles fluid temperatures between +2°C and +110°C. Exercise caution when working with hot water to prevent burns.
• दबाव: The maximum operating pressure is 10 bar. Ensure the system components can withstand this pressure.
• प्रतिष्ठापन वातावरण: Install the pump in a dry, well-ventilated area, protected from frost and direct weather exposure.
• वैयक्तिक संरक्षणात्मक उपकरणे: Always wear appropriate personal protective equipment (e.g., gloves, safety glasses) during installation and maintenance.

3. स्थापना पुस्तिका

Proper installation is crucial for the pump's efficient and safe operation.

3.1 प्री-इंस्टॉलेशन चेक

• Verify that the pump's specifications (voltage, frequency, pressure) match your system requirements.
• Ensure the installation location provides adequate space for mounting and future maintenance.
• Confirm that the piping system is clean and free of debris.

3.2 पंप बसवणे

1. The pump has an installation length of 180 mm. Ensure sufficient space between pipe connections.
2. Install the pump in the return line of the heating system, if possible, to extend its lifespan by operating at lower temperatures.
3. Ensure the motor shaft is horizontal to allow for proper lubrication of the bearings.
4. Use the provided seals (gaskets) to ensure a watertight connection to the piping. The connection diameter is 1 1/2"/1".
5. Tighten all connections securely but avoid over-tightening.

3.3 इलेक्ट्रिकल कनेक्शन

1. Ensure the main power supply is switched off at the circuit breaker.
2. Connect the pump to a 1 x 230 V, 50 Hz power supply.
3. The pump has an IP44 protection rating. Ensure the electrical connections are protected from moisture.
4. Follow the wiring diagram provided on the pump's terminal box cover.
5. योग्य ग्राउंडिंग सुनिश्चित करा.

४.३ सिस्टम फिलिंग आणि व्हेंटिंग

1. After installation, fill the heating system with water.
2. Vent the system thoroughly to remove any trapped air. Air in the system can cause noise and reduce pump efficiency.
3. The pump may have a manual vent screw; open it carefully until water flows out, then close it.

4. ऑपरेटिंग सूचना

The IBO OHI 25-60/180 pump features a manual 3-speed selector to adjust performance.

4.1 प्रारंभिक स्टार्ट-अप

1. Ensure the system is filled with water and properly vented.
2. Turn on the main power supply to the pump.
3. Select a speed setting using the rotary switch on the pump's control panel.

4.2 गती सेटिंग्ज

The pump offers three speed levels, each with different power consumption, maximum flow rate (Q max), and maximum head (H max):

• स्तर I: 46 W power consumption, 22 l/min maximum flow, 3 m maximum head.
• स्तर II: 63 W power consumption, 38 l/min maximum flow, 5 m maximum head.
• स्तर III: 93 W power consumption, 55 l/min maximum flow, 6 m maximum head.

Adjust the speed setting based on the heating system's requirements to achieve optimal circulation and energy efficiency.

5. देखभाल

Regular maintenance ensures the longevity and efficient operation of your circulation pump.

६.१ नियमित तपासण्या

• व्हिज्युअल तपासणी: Periodically check the pump for any signs of leaks, corrosion, or damage to the casing or electrical connections.
• आवाज पातळी: Listen for any unusual noises during operation, which could indicate air in the system or a mechanical issue.
• तापमान: Ensure the pump is not overheating.

5.2 स्वच्छता

Keep the exterior of the pump clean and free from dust and debris to ensure proper heat dissipation.

७.४ हिवाळीकरण (लागू असल्यास)

If the heating system is to be shut down for an extended period in freezing temperatures, ensure the system, including the pump, is drained to prevent frost damage.

6. समस्या निवारण

This section provides guidance for common issues. For complex problems, consult a qualified technician.

7. तांत्रिक तपशील

8. हमी आणि समर्थन

Information regarding the product warranty is not provided in the available data. For warranty claims, technical support, or spare parts inquiries, please contact the original seller or the manufacturer, 4U-Onlinehandel, directly. Keep your purchase receipt as proof of purchase.