Hayward DEX4820BTC Filter Head with Clamp System Replacement Instruction Manual

1. परिचय

This instruction manual provides essential information for the safe and effective installation, operation, and maintenance of your Hayward DEX4820BTC Filter Head with Clamp System Replacement. This component is designed to replace the filter head and clamp system on specific Hayward pool filters. Please read this manual thoroughly before proceeding with installation or maintenance.

2. सुरक्षितता माहिती

WARNING: Failure to follow these instructions can result in severe injury or death.

• Always disconnect power to the pump and filter system before performing any service or maintenance.
• Relieve all pressure from the filter system before opening the filter. Refer to your main filter manual for specific pressure relief procedures.
• Ensure all connections are secure and leak-free after installation.
• Do not operate the filter system if any part is damaged or missing.
• This product must be installed and serviced by a qualified pool professional in accordance with all applicable local codes and ordinances.

3. पॅकेज सामग्री

The Hayward DEX4820BTC Filter Head with Clamp System Replacement package typically includes:

• 1 x Filter Head
• 1 x Clamp System (including clamp, bolt, nut, and washer)
• 1 x O-ring (for filter head seal)

Figure 1: Hayward DEX4820BTC Filter Head with Clamp System. This image shows the brown, dome-shaped filter head with the 'LOCK' and 'UNLOCK' indicators visible on the top, and the base where the clamp system attaches.

१०.२. सुसंगतता

This filter head with clamp system replacement is compatible with the following Hayward filter models:

• Hayward Pro Grid Vertical D.E. Filter Models: DE2420, DE3620, DE4820, DE6020, DE7220
• Hayward Swim Clear Cartridge Filter Models: C2020, C3020, C4020, C5020
• Hayward Skim-Master Models: SP1070, SP1070 NSF

5. स्थापना सूचना

Follow these steps carefully to install the replacement filter head and clamp प्रणाली

1. फिल्टर सिस्टम तयार करा:
   • Turn off the pool pump and any automatic controls.
   • Close all valves leading to and from the filter to isolate it.
   • Open the air relief valve on the top of the filter to release any trapped air and pressure. Ensure the pressure gauge reads zero.
   • Open the filter drain plug to drain water from the filter tank.
2. Remove the Old Filter Head:
   • Once the filter is depressurized and drained, loosen the clamp system that secures the old filter head to the filter tank.
   • Carefully remove the old filter head and clamp. Inspect the filter tank's sealing surface for any debris or damage. Clean if necessary.
3. Install the New Filter Head and O-ring:
   • Inspect the new O-ring for any cuts or damage. Lightly lubricate the O-ring with a silicone-based lubricant specifically designed for pool equipment.
   • Place the lubricated O-ring into the groove on the filter tank or the new filter head, ensuring it is seated correctly and evenly.
   • Carefully position the new filter head onto the filter tank, aligning it properly.
4. Secure with the New Clamp प्रणाली:
   • Place the new clamp system around the flange of the filter head and the filter tank.
   • cl द्वारे बोल्ट घालाamp ends and secure it with the nut and washer.
   • cl घट्ट कराamp bolt evenly and gradually using a wrench. Alternate tightening sides to ensure even pressure around the entire clamp. Do not overtighten, as this can damage the clamp or filter components. The clamp should be snug, holding the head firmly in place without excessive force.
5. सिस्टम रीस्टार्ट करा:
   • Close the filter drain plug.
   • Open the valves leading to and from the filter.
   • With the air relief valve still open, turn on the pool pump.
   • Allow the filter tank to fill with water and air to escape through the air relief valve. Once a steady stream of water emerges from the air relief valve, close it.
   • Check for any leaks around the filter head and clamp system. If leaks are present, turn off the pump, relieve pressure, and re-tighten the clamp.

५. ऑपरेटिंग विचार

Once installed, the filter head operates as part of your overall pool filtration system. Ensure your main filter and pump are operating within their recommended pressure ranges. Regularly monitor the pressure gauge on your filter head. An increase in pressure typically indicates that the filter media needs cleaning or backwashing, depending on your filter type.

7. देखभाल

Proper maintenance extends the life of your filter head and ensures optimal system performance.

• O-ring Inspection and Lubrication: Annually, or whenever the filter head is removed, inspect the O-ring for cracks, tears, or flattening. Replace if damaged. Always lubricate the O-ring with a silicone-based lubricant before reassembly to ensure a proper seal and prevent premature wear.
• Clamp सिस्टम तपासणी: वेळोवेळी cl तपासाamp system for corrosion, cracks, or deformation. Ensure the bolt and nut are securely tightened. Replace any damaged clamp घटक ताबडतोब.
• सामान्य स्वच्छता: Keep the exterior of the filter head clean from dirt and debris.

8. समस्या निवारण

If you encounter issues after installing your new filter head, consider the following:

9. तपशील

• मॉडेल क्रमांक: DEX4820BTC
• आयटम वजन: 19 पाउंड
• निर्माता: हेवर्ड

10. हमी आणि समर्थन

For warranty information and technical support, please refer to the official Hayward website or contact Hayward customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.

Hayward Customer Service: www.hayward-pool.com