परिचय
This manual provides instructions for the installation, operation, and maintenance of the Linear Multi-Code Keypad Transmitter, model 420001. This wireless keypad is designed for use with Multi-Code Receivers to control access to garage doors or gates.
उत्पादन संपलेview
The Linear Multi-Code Keypad Transmitter 420001 is a 12-button alphanumeric keypad. It operates on a 300 MHz frequency and features 10 dip switches for programming. Its weatherproof casing बाहेरील वापरासाठी टिकाऊपणा सुनिश्चित करते.
प्रतिमा: समोर view of the Linear Multi-Code Keypad Transmitter 420001, showing the 12-button alphanumeric keypad and the "MULTI-CODE" branding at the top.
सेटअप आणि स्थापना
बॅटरी स्थापना
The keypad requires one 9V alkaline battery (not included). To install:
- Open the keypad casing.
- Connect the 9V battery to the battery clip.
- Place the battery securely within the compartment.
- Close the keypad casing, ensuring it is sealed properly for weather resistance.
आरोहित
The keypad is designed for screw-in installation and mounts with two screws.
- Choose a suitable location for mounting, ensuring it is within range of your Multi-Code Receiver.
- Mark the positions for the two mounting screws.
- आवश्यक असल्यास पायलट छिद्र ड्रिल करा.
- Secure the keypad to the surface using appropriate screws.
कीपॅड प्रोग्रामिंग
This keypad uses 10 dip switches for programming. The code is entered directly through the keypad, eliminating the need to manually adjust physical dip switches on the unit itself.
- Locate the dip switch settings on your Multi-Code Receiver or existing remote. This will be a sequence of 10 switches, each set to ON, OFF, or MIDDLE (if applicable).
- On the 420001 keypad, enter the 10-digit code corresponding to your receiver's dip switch settings. Refer to the keypad's internal instructions for specific key presses to represent ON, OFF, or MIDDLE positions.
- Press the "ACCESS" button to save the code.
- Test the keypad to ensure it operates your garage door or gate opener.
टीप: Programming typically takes less than 2 minutes. Ensure the keypad is within operational range of the receiver during testing.
ऑपरेटिंग सूचना
To operate your garage door or gate using the Linear Multi-Code Keypad Transmitter:
- Enter your programmed 10-digit access code using the alphanumeric buttons.
- Press the "ACCESS" button.
- The LED indicator will illuminate, and your Multi-Code Receiver should activate, opening or closing your garage door or gate.
If the door or gate does not respond, verify your code and ensure the keypad is within effective range of the receiver.
देखभाल
- बॅटरी बदलणे: When the keypad's performance degrades or the LED indicator fails to light, replace the 9V battery. Follow the battery installation steps.
- स्वच्छता: Clean the keypad's exterior with a soft, damp कापड. अपघर्षक क्लीनर किंवा सॉल्व्हेंट्स टाळा.
- हवामान प्रतिकार: The keypad features a weatherproof casing. Ensure the casing is properly closed and sealed after any internal access (e.g., battery replacement) to maintain its weather-resistant properties.
समस्यानिवारण
| समस्या | संभाव्य कारण | उपाय |
|---|---|---|
| Keypad does not respond or works intermittently. |
|
|
| एलईडी इंडिकेटर उजळत नाही. | बॅटरी खराब झाली आहे किंवा चुकीच्या पद्धतीने बसवली आहे. | Check battery connection or replace the 9V battery. |
| Keypad does not program correctly. | Incorrect dip switch settings entered. | Double-check the 10 dip switch settings from your receiver and re-enter the code carefully. |
तपशील
| मॉडेल क्रमांक | 420001 |
| ब्रँड | रेखीय |
| वारंवारता | 300 MHz |
| Number of Dip Switches | 10 |
| उर्जा स्त्रोत | 1 x 9V Alkaline Battery (not included) |
| स्थापना प्रकार | स्क्रू-इन |
| उत्पादन परिमाणे | 6.75 x 1.5 x 3 इंच |
| आयटम वजन | 4 औंस |
| साहित्य | प्लास्टिक |
| रंग | बेज |
| अनुपालन | FCC |
हमी आणि समर्थन
वॉरंटी माहिती किंवा तांत्रिक समर्थनासाठी, कृपया उत्पादकाच्या अधिकाऱ्याचा संदर्भ घ्या webवेबसाइटवर जा किंवा त्यांच्या ग्राहक सेवा विभागाशी संपर्क साधा. वॉरंटी दाव्यांसाठी तुमची खरेदी पावती ठेवा.
निर्माता: रेखीय
